638184

WOLF-Garten 1.40 XC Manual

13
Zoom out
Zoom in
Previous page
1/36
Next page
13
G
z Switch off the lawnmower, pull the mains plug and wait for the
lawnmower to stop running if, for example:
– leaving the lawnmower
– unblocking a blade
– intending to check, clean or work on the lawnmower
– you have encountered a foreign object, in which case you
should check the lawnmower for damage and carry out any
necessary repairs.
– the lawnmower is vibrating heavily (switch off immediately
and ascertain the cause).
– you wish to change the settings or carry out cleaning work.
– you wish to check whether the connection cables have be-
come tangled or damaged.
– If the connection cable is damaged during use, it must be
immediately disconnected from the mains power supply.
Do not touch the cable before it has been disconnected
from the mains power supply.
Maintenance
1 Attention! Rotary cutter blade
Before all maintenance and cleaning work:
z Pull out the power plug.
z Do not touch running blades.
z Never spray down the lawnmower using water, especially not
at high pressure.
z Regularly check and tighten all visible screws and nuts, espe-
cially those relating to the cutting bar, to ensure a firm fit.
z Always have blades changed or re-sharpened by a specialist
workshop, since a balance test must be carried out as speci-
fied in the safety regulations following any removal of parts.
z Only use original WOLF spare parts. Otherwise we can’t gua-
rantee that your mower conforms to the safety regulations.
z Never park your lawnmower in damp rooms.
z For safety reasons, replace worn or damaged parts.
Disposal
Assembly
Fasten handle bars
1 Caution!
The cable can be damaged while folding up or pulling out
the handle bar.
z Inlay the cable in the bend protection .
z When adjusting the handle height take care that the ca-
ble is not crimped
1. Fold the bottom part of the handle up and screw it tight with
the two hand wheels .
2. Set the handle to the desired height .
3. Fold the upper part of the handle out and screw it tight with the
wing nuts .
Mount the collecting bag
1. Place the chute (1) on the collecting bag flap (2) .
2. Press the chute from behind onto the collecting bag flap. The
chute is ready for use as soon as it locks into place .
Operation
Operating times
z Please check noise abatement regulations prevailing in your
country.
Feed cable through the strain relief
z Please feed cable through the strain relief .
Hang up collection bag
1 Attention! Rotary cutter blade
Undertake adjustments on the equipment only after the
motor is switched off and the cutting tool has come to a
standstill.
1. Lift the protective flap.
2. Hang the grass bag in the chassis with the hooks in the reces-
ses (see arrow).
3. Replace the protective flap.
Set cut height
1 Attention! Rotary cutter blade
Undertake work/adjustments on the equipment only after
the motor is switched off and the cutting tool has come to a
standstill.
1. Pull the lever out .
2. Set the desired cutting height .
3. Press the lever back in .
Selection of Cutting height
z If possible, mow when grass is dry in order to protect turf. Do
not se cutting position too low when mowing very hight or wet
grass.
z We recommend an average cutting height of 40-50 mm.
Do not dispose of electrical equipment in domestic
waste. Recycle equipment, accessories and pa-
ckaging in an environment-friendly manner.
A
B
C
D
A
C
B
C
D
E
F
G
E
F
G
H
H
J
K
L
M
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for WOLF-Garten 1.40 XC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of WOLF-Garten 1.40 XC in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Turkish, Norwegian, Finnish as an attachment in your email.

The manual is 1,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info