Manual Wodtke Frank SX waterplus S4 (page 72 of 83) (German)

813089

Zoom out

Zoom in

1/83

Bedienungsanleitung Steuerung S4_2006_09_25-neu.doc Page 72 / 83

9.12 Inspecting and cleaning electrical components (all models)

First ensure that the mains plug has been disconnected. Inspect the run of electrical cables.

Especially make sure that cables do not pass over sharp edges or hot places and that

they show no tears or bare wire. Torn or otherwise damaged cables must be replaced. Clean

any electrical components that are covered with dust using a paint brush. Use a suitable

scraping tool to remove any corrosion on electrical contacts.

9.13 Inspecting and cleaning convection air ducts (all models)

It is advisable to inspect all convection air passages (including those beneath the side panels

and between the heat reflector plates) once a year and use a vacuum cleaner or paint brush to

clean wherever large amounts of dust have accumulated.

9.14 Inspecting and cleaning the pellet chute and temperature sensor TP (all

models)

The pellet chute that runs from the fuel hopper to the burner pot must be cleaned thoroughly

with a wire brush or the like (taking care to remove any tar, caked on dust, pellet residues,

burnt-in pellet residues) to keep it smooth, thus ensuring that pellets can easily slide into the

burner pot and dust does not accumulate on the chute. Take care not to damage temperature

sensor TP, which is located in the chute, and check with a mirror that it is free of soot and any

deposits. If necessary, and only then, dismount TP from behind and use a brush to carefully

clean it of soot, pellet dust etc. Make sure TP is remounted in the correct position and at the

correct depth (see relevant chapter in the assembly instructions).

9.15 Finishing servicing work, test run, and service reset (all models)

After completing all servicing work re-establish all connections and perform a test run. Only

when you have completed all the above-named servicing routines should you do a service reset

(counter reset) via the operating panel. Take the values of parameters “BG” (total operating

hours) and “PG” (total pellet consumption) down in a logbook after every servicing, and keep

the logbook in a safe place. In this way you will always have a record of past servicing work in

case it should ever be necessary to call a technician.

 How to do a service reset after completing all work:

To do a service reset you first have to enter “PW” at menu level 1!

With the appliance switched on, do the following:

• Press the “Menu” key; the display will then show the installed basic software (for ex. S4

002)

• Press the “+” or “–” key repeatedly until the display shows “PW”.

• Starting from “PW”, press the “+” and the “–” key simultaneously for 4 seconds until

the displayed value jumps back to –1.5. Now the service reset has been completed.

• Press the “Menu” key once more or wait for 60 seconds until the appliance changes to the

operating level.

An expert tip:

Have you really cleaned the firebox, heat exchanger, all flueways, the flue gas fan and flue

connector completely and consistently? In order for a service routine to have been effective

the flue gases must be able to pass uninhibited from the burner pot all the way into the

chimney. It’s not that everything must shine afterwards, but rather that just one bottleneck

along this path can hinder the removal of flue gas and lead to malfunctioning. So it is pointless

to polish one particular place if you are careless about or completely neglect another. The entire

flue gas passage must be cleared of any obstructing material and free.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Wodtke Frank SX waterplus S4 in the language / languages: German as an attachment in your email.

The manual is 3.18 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Wodtke Frank SX waterplus S4

Wodtke Frank SX waterplus S4 User Manual - German - 76 pages

Wodtke Frank SX waterplus S4 User Manual - French - 80 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Wodtke Frank SX waterplus S4 Manual

Product: