813089
21
Zoom out
Zoom in
Previous page
1/83
Next page
Bedienungsanleitung Steuerung S4_2006_09_25-neu.doc Page 21 / 83
© wodtke GmbH Tübingen. All rights reserved. Subject to change without notice. Month of issue xx/2007 Art. No. 950 281
Important information:
Do not restart the appliance immediately or within too short a time, but leave it to cool
off in “G OFF” for at least 5 minutes before starting again. In this way you will avoid
overheating the appliance.
Be sure to keep the firedoor closed during the ignition phase and do not switch the
appliance on and off repeatedly.
If the appliance is switched off during preheating programme “A”, the ignition
element remains active for the remainder of its set operating time of 10 minutes, i.e.
even when the display already shows “G OFF” for fan after-run. When the preheating
programme is aborted pellets that are already in the burner pot are lit all the same!
The purpose of this is to burn away all the pellets left in the burner pot, so that it will
be empty at the next start and the preheating programme can start again without
difficulty.
It can take up to 10 minutes from ignition until the first flame becomes visible
(depending on how clean the burner pot is as well as on pellet quality).
The preheating programme starts anew after every restart or power failure.
If the preheating programme doesn’t work properly (burner pot still full of unburnt
pellets), be sure to observe the instructions in Chapters 0. and . Clean the burner
pot thoroughly of pellets and ash/slag before every restart. Do not restart the
appliance right away:
Danger of overheating and fire!
5.12 Heating programme “H” (normal operation)
= display shows “H” for heating programme
= display shows flashing dot for feed screw operation
= display shows thermal output in kW
5.12.1 Heating programme when thermal output is set manually
In the heating programme the appliance delivers the manually preset
output unless an external controller or an internal safety function
requires otherwise. This provides an easy and convenient way of
operating the appliance at the desired output level via the +/- keys.
With the +/- keys you can change the previously set output level in
0.5 kW steps at any time. However, manual changes in thermal
output only become effective when there are no contradicting
requirements from an external controller or an internal safety
function.
When thermal output has been changed manually while an external
controller or internal safety function is active, the value shown in the
display will change back to the value required by that controller or
function.
H .
4,5
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Wodtke Frank SX waterplus S4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Wodtke Frank SX waterplus S4 in the language / languages: German as an attachment in your email.

The manual is 3.18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Wodtke Frank SX waterplus S4

Wodtke Frank SX waterplus S4 User Manual - German - 76 pages

Wodtke Frank SX waterplus S4 User Manual - French - 80 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info