Manual Wodtke Frank SX waterplus S4 (page 8 of 83) (German)

813089

Zoom out

Zoom in

1/83

Bedienungsanleitung Steuerung S4_2006_09_25-neu.doc Page 8 / 83

design category 1 according to DIN 18891. The flue draught (chimney draught = negative

pressure) must range between 0 Pa minimum and 20 Pa maximum. A chimney calculation prior

to installation is mandatory (DIN 4705 or EN 13384). The chimney has an important safety

function in the event of a power failure and must be correctly dimensioned so as to ensure that

flue gas is carried off safely from the appliance. In the case of excessive chimney draught we

recommend installing a draught limiter.

2.7 Combustion air supply

wodtke stoves use room air for combustion, and a sufficient supply of combustion air is

therefore essential. The air pressure in the room of installation must not be negative. Please

observe the relevant technical rules / regulations and any additional information provided by

wodtke when operating your appliance in combination with air conditioning systems (for ex.

ventilation systems, exhauster hoods, pneumatic conveyor systems etc.). The use of a type DS

01 wodtke differential pressure switch with accessories (see price list) is mandatory to

ensure safety in the case of combined operation with a ventilation system.

2.8 Pellet quality

All statements on DIN-certified pellet quality in this documentation refer to an ash content of

0.25%, 650 kg/m³ bulk density and a minimum calorific value H

of 4.9 kWh/kg. 1000 kg of

pellets of this specification have an energy content equivalent to 500 litres of heating oil and

require approx. 1.54 m³ of storage space. Please observe the notes on in this in Chapter 11

(Approved fuels). Deviations from these specifications are unavoidable due to the DIN tolerance

ranges allowed for pellets in terms of, for. ex., ash content, bulk density, composition and pellet

size / geometry, and this in turn leads to deviations in other parameters. In the event of high

bulk density, special geometries or high calorific value of pellets it can happen that internal

safety devices temporarily lower the thermal output of the appliance until the desired values (=

nominal thermal output) are complied with again. This is in no way a shortcoming. The

appliance then goes into modulation mode (see Chapters 0 and 0).

2.9 How to increase return flow temperature in Waterplus appliances

Return flow temperature at the water inlet must be at least 50 °C (ideally 55 °C), since

otherwise soot and tar can accumulate. wodtke provides special hydraulic connection pieces for

this purpose.

2.10 Cleaning, care and servicing

Unlike liquid and gaseous fuels solid fuels always leave ash and soot behind as combustion

residues. Although the combustion quality and operating comfort of wodtke appliances are

vastly superior to that of conventional wood fired stoves, this advantage does entail the effort of

regular cleaning and maintenance to keep the appliance clear of soot and ash. Neglect of

cleaning and servicing can result in operating trouble for which the manufacturer cannot be held

liable. Please observe the relevant instructions in Chapters 0 and 9. Regular cleaning, care and

servicing will also help to maintain the efficiency of your stove, since soot is an excellent heat

insulator and can therefore reduce heat dissipation and thermal efficiency considerably.

2.11 Mains voltage / Power supply

230 VAC / 50 Hz. Voltage fluctuations between 195 and 255 V are admissible.

Automatic identification / switchover to 200 VAC / 60 Hz.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Wodtke Frank SX waterplus S4 in the language / languages: German as an attachment in your email.

The manual is 3.18 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Wodtke Frank SX waterplus S4

Wodtke Frank SX waterplus S4 User Manual - German - 76 pages

Wodtke Frank SX waterplus S4 User Manual - French - 80 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Wodtke Frank SX waterplus S4 Manual

Product: