813148
55
Zoom out
Zoom in
Previous page
1/68
Next page
Manual_S5_Airplus_2015_04_20 Page 55 / 68
© Wodtke GmbH - Tübingen. All Rights and Changes Reserved.Printed 04/2015 Part No. 950 976
Class 1 fault code
Cause of fault
Resolution of fault
LM Er1 =
air volume sensor break
Case A: air volume sensor break (= component error)
Case B: external error due to exhaust gas back-flow. Sen-
sor element temperature > 120 °C (also see error descrip-
tion for TL). If the sensor is heated to values > 120 °C due
to exhaust back-flow, this is evaluated as a component er-
ror (break) and the display switches to LM Er1. If the
unit/the sensor has cooled and the sensor is not perma-
nently damaged, the unit can be switched on again.
Case A: Replace air volume sen-
sor + reset via I/O button.
Case B: Air volume sensor does
not need to be replaced. Find / re-
solve external error (for reasons,
see errors TL, Hi / TL Grd) then re-
set via I/O button.
LM Er2 =
Air volume sensor short-
circuit
Short circuit = component error
Test / replace air volume sensor +
reset via I/O button.
TR Er1 =
Flue gas sensor break
Break = component error
Test / replace TR + reset via I/O
button.
TP Er1 =
Pellet chute sensor break
Break = component error
Test / replace TP sensor + manu-
ally reset via
I/O button.
TP Er2 =
Pellet chute sensor short-
circuit
Short circuit = component error
Test / replace TP sensor + manu-
ally reset via
I/O button.
HB Er1 =
control board break or
break in connection cable
from control board to main
board or communication
with Touch Control TC1
(option) disrupted
Break = component error
First test connection cable for con-
tinuity/polarity, etc. and only there-
after test/replace control
board/TC1 and manual reset via
I/O button. If the display is broken,
the error is displayed even if the
new control board is already con-
nected. Then briefly press the I/O
button so that the unit recognises
the new control board.
RE Er1 =
Bridge on "Reserve input"
is open
Bridge wire on "Reserve input" open or error on external
component/unit.
Notice: The "Reserve input" serves for feedback from ex-
ternal accessories. It is verified 15 seconds after each start
whether this input is bridged; that is, closed. Only then does
the unit go into the heating programme. The "Reserve in-
put" is then continually inspected. If the bridge on the "Re-
serve input" is opened, a fault shut-down / safety function
occurs (Class 1 error).
Application examples (also see assembly instruc-
tions):
1) Flue gas damper for flue gas: if a mechanical motorised
flue gas damper is used, the normally open contact of this
damper can be connected to the Reserve input. The wodtke
Pellet Primärofen then only operates if the flue gas damper
is opened. If an error occurs on the flue gas damper, the
unit is deactivated via the safety function. The flue gas
damper must open completely by motor within 15 sec, as
otherwise there is an error message because the feedback
to the unit occurs too late.
2) Intake damper for combustion air: for the combustion air:
function, application and wiring like in a flue gas damper.
3) Interlock with ventilation system / extraction hood: if the
ventilation system or extraction hood has a potential-free
output as the operating signal, this output can be con-
nected to the Reserve input as normally closed. The wodtke
Pellet Primärofen only operates if the extraction hood/ven-
tilation is not operating. All described examples can be con-
nected electrically in series so that the wodtke Pellet
Primärofen only operates if all external devices are func-
tioning, or deactivates as soon as one single device has a
malfunction.
Check wire bridge on "Reserve in-
put" and insert correctly.
If an external component is con-
nected, check external component
for correct wiring/function (espe-
cially normally open contact) and
replace if necessary.
Afterwards, manual reset via I/O
button.
Attention: A reset of the "RE
Er1" error message and a restart
as a result is only possible if the
"Reserve input" is bridged
(closed) again.
Note: In the case of external de-
vices connected in series, all ex-
ternal devices and the entire ex-
ternal wiring must be inspected.
Fault code
Class 1
Cause of fault
Resolution of fault
55


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Wodtke Easy.nrg S5 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Wodtke Easy.nrg S5 in the language / languages: English as an attachment in your email.

The manual is 6.01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Wodtke Easy.nrg S5

Wodtke Easy.nrg S5 User Manual - German - 68 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info