484837
6
Zoom out
Zoom in
Previous page
1/11
Next page
10 11
DEGBFR
Cleaning and service
Pull out the power plug prior to cleaning. Never immerse the
kettle and the base in water. Briefly rinse the kettle from time
to time. Wipe the outside of the appliance only with a damp
cloth. Do not use harsh or abrasive cleaning agents.
The mesh filter in the spout can be removed for cleaning
when the lid is open. To do so, press the top lug downwards.
To reinsert the mesh filter, position the mesh filter in the middle
of the spout and then push forward to lock into place. The he-
ater bottom is made of stainless steel. If you notice rust marks
nevertheless, these are only deposits sticking to the surface.
Remove them immediately with a cleaning agent for stainless
steel.
Decalcifying
Calcium deposits result in energy losses and impair the service
life of the appliance. The appliance will switch off prematurely
if the calcium deposits are too strong. It is then very difficult to
remove the deposits. Decalcify the appliance regularly.
Therefore, the pot should be regularly descaled with usual
descaling agents suitable for stainless steel. Please consider the
user instructions of the manufacturer. Pour out the water and
rinse the kettle thoroughly with cold tap water. Do not heat up
the kettle during the decalcification process.
Important. Warranty compensation does not exist for damage
that occurs due to non-compliance with the decalcification
instructions.
Causes of faults
· The appliance switches off before boiling
There are excessive calcium deposits on the bottom
of the kettle, or
· The appliance does not switch off
Close the cover until it locks into place.
The mesh filter is not correctly fitted.
· The kettle does not pour properly
Decalcify the mesh filter.
· The appliance cannot be switched on
The kettle has not cooled down sufficiently after
being operated with no or too little water.
If the fault cannot be remedied, you must return the appliance
for repair.
For UK use only
· This product is supplied with a 13 A plug conforming to BS
1363 fitted to the mains lead. If the plug is unsuitable for
your socket outlets or needs to be replaced, please note the
following. If the plug is a non-rewireable one, cut it from
Start-up
Prior to using for the first time, clean the inside of the kettle
thoroughly. To do so, pull the lid lock to open the lid. A mesh
filter is fitted in the spout to hold back large pieces of calcium
deposits when pouring out the water.
The section of the power cable not in use, can be wound
up and stored on the base. Connect the power plug to a
shockproof socket.
Fill in at least as much water that it can be seen in the window,
but not further than the max. mark. Close the lid and make sure
it locks into place. Otherwise the automatic boil-stop function
cannot function properly.
Place the kettle onto the base pointing in any direction. Only
then press down the ON switch under the handle. The indica-
tor light on the ON switch will indicate that the appliance is
heating up.
The ON switch will only lock into place if the kettle is positioned
on the base.
Due to the high level of power consumption during the boiling
process, you will notice an increase in noise.
Do not use the water from the initial boiling operation for food
purposes.
Automatic switch-off
A short time after the water has started to boil, the automatic
boil-stop function will switch off the appliance. If the kettle is
filled with only a small quantity of water, the switch-off time
will increase.
If you require only warm water, the heating process can be
cancelled at any time by pressing the ON switch. The appliance
will switch off automatically after the kettle is removed from
the base. If you want to reboil hot water, the appliance can be
switched on again.
For functional reasons, some condensed water may run from
the openings at the bottom of the kettle onto the rim of the
base. This is necessary for technical reasons and does not impair
the safety of the appliance.
Safety system
If the kettle is accidentally operated without water, a thermo-
stat will protect the kettle from overheating by switching off
the appliance.
Before filling in water, leave the kettle to cool down for 5-10
minutes.
If the first thermostat fails due to incorrect use, an additional
temperature limiter offers reliable protection.
BAL_waterkettle_BrandLoyalty_148x210_RZ.indd 10-11 20.04.11 16:04
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Wmf WMF 3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Wmf WMF 3 in the language / languages: English, German, French as an attachment in your email.

The manual is 2,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info