690815

Wmf SKYLine - 17020021 Manual

8
Zoom out
Zoom in
Previous page
1/44
Next page
8
Note: The cup information given on the portion selector switch (5) is for guidance only. A different
setting may be required for different kinds of coffee, cup sizes, water hardness and also your personal
preference.
Test out which setting suits your personal preference.
The grinding process begins once the start/stop button has been pressed (6). The motor only runs if the
collection container (7) has been put in place properly.
Once the required amount of coffee has been ground, the mill shuts off automatically.
The grinding process can be interrupted at any time by pressing the start/stop button (6) again.
Wait until the motor has stopped before removing the collection container (7). Press down slightly
when removing the collection container (7). The coffee powder can be placed directly in the coffee
machine filter.
To avoid loss of aroma, coffee should only be milled for immediate use.
Excess coffee grounds can be kept in the collection container (7). Then close the collection container
(7) with the rubber cap (1).
Important information:
If the mill does not run, the motor may be obstructed by a bean. In this case select a higher degree of
fineness. Once the motor is running the desired degree of fineness can be immediately reselected after
start-up.
If the motor still does not start, or has difficulty starting up at the highest degree of fineness, clean
the mill as described under „Cleaning and Care“.
Cleaning and care
Warning! Remove from the mains before cleaning. Under no circumstances submerge the device in
water - wipe the outside with a damp cloth instead.
Do not use scourers.
Remove the collection container (7) and clean with a mild cleaning product. Dry well before replacing
the collection container (7).
Remove the remaining beans before removing the bean hopper (3). Clean the bean hopper (3) and
bean hopper cap (2) in dish water and dry well. The mill can be opened when malfunctions occur or
for cleaning. Remove the bean hopper (3) and then remove the mill ring (8). Clean the mill and the
mill ring (8) with a small brush or the cleaning brush included in delivery (9).
Warning: The mill has sharp edges - there is danger of injury.
Replace the mill ring (8) and turn until it clicks into place and only
moves slightly.
Important: The safety ring must be turned in a clockwise direction as
far as it can go (see illustration) before the bean hopper (3) is replaced.
Otherwise the bean hopper (3) cannot be put back in place. Should
the safety ring be incorrectly replaced during cleaning, you can turn it
manually to the left.
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Wmf SKYLine - 17020021 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Wmf SKYLine - 17020021 in the language / languages: English, German, Dutch, Danish, French, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info