774433

Wilfa Trysil Floor Comfort Manual

75
Zoom out
Zoom in
Previous page
1/84
Next page
11
English
8
/
Press this button to operate the on/off for the healthy and scavenging functions in operating status. Press this button for the
first time to start the scavenging function; the LCD will display ”
/
”. Press this button a second time to start the healthy and
scavenging functions simultaneously; the LCD will display“
/
” and “
/
”. Press this button a third time to exit the healthy and
scavenging functions simultaneously. Press this button a fourth time to start the healthy function; the LCD will display “
/
”.
Press this button again to repeat the operations above.
9 SLEEP
• Press this button to select Sleep 1 ( 1), Sleep 2 ( 2),Sleep 3 ( 3) or to cancel Sleep. Scroll between these selections after
the unit is powered on. Sleep Cancel is the default value.
• Sleep 1 is Sleep mode 1 in Cool, Dehumidify modes. The sleep status after running for one hour: the main unit
temperature setting will increase by 1 °C; after two hours: the temperature setting will increase by 2 °C and the unit will
continue to run at this temperature setting. In Heat mode, the sleep status after running for one hour: the temperature
setting will decrease by 1 °C; after two hours: the temperature setting will decrease by 2 °C and the unit will continue to run
at this temperature setting.
• Sleep 2 is Sleep mode 2, where the air conditioner will run according to a preset group of temperature settings along a
sleep temperature curve.
• Sleep 3, which is a Sleep mode containing DIY sleep curve settings:
(1) In Sleep 3 mode, press and hold the ”Turbo” button. The remote control will enter individual sleep setting status and
will display "1 hour". The temperature setting field ("88") will display the corresponding temperature of the last setting
in the sleep curve and flash. (The first entry will display in accordance with the initial sleep curve setting value from the
factory);
(2) To adjust, use the ”+” and ”-” buttons to change the corresponding temperature setting. After adjustment is complete,
press the "Turbo" button again to confirm;
(3) At this point the timer position on the remote control will automatically advance by 1 hour, i.e., to "2 hours", "3 hours",
"8 hours", etc., The temperature setting field ("88") will display the corresponding temperature of the last setting in the
sleep curve and flash;
(4) Repeat steps (2) - (3) above until 8 hours of temperature settings have been input. The sleep curve set up is now
finished. At this point the remote control will revert to the original timer display and the temperature display will return to
the original temperature setting. The Sleep 3 DIY sleep curve set up can be reviewed:
• The user can use the sleep curve setting method to review the preset sleep curve. Enter individual sleep setting status
but do not change the temperature. Press the "Turbo" button directly to confirm. Note: In this presetting/review method,
if no button is pressed continuously within 10 seconds, the sleep curve setting status will automatically exit and revert to
the original display. Similarly, if the "ON/OFF", "Mode", "Timer" or "Sleep" buttons are pressed, the sleep curve setting/
review status will also exit.
10 TEMP
Use this button to select display of the indoor temperature setting or the indoor ambient temperature. When the indoor unit is
first powered on, it will display the temperature setting. If the temperature display status is changed from another status to
”
/
”, it will display the ambient temperature. If within 5 seconds or 5 seconds later, the unit receives another remote control
signal, this will return the display to the temperature setting. If the user has not set up the temperature display status, the unit
will display the temperature setting.
11 QUIET
Use this button for Quiet status, which is available in Auto Quiet mode (display ” ” and ”Auto” signal), Quiet mode (display
” ” signal) and Quiet OFF (no signal for ” ” is displayed). After powering on, the unit defaults to Quiet OFF. Note: the Quiet
function cannot be set up in Fan and Dry mode; in Quiet mode (Display ” ” signal), the fan speed is not available.
12 CLOCK
Press the CLOCK button and will flash. Within 5 seconds press the + or - button to adjust the present time. Holding down
either button for more than 2 seconds will increase or decrease the time by 1 minute every 0.5 seconds and then by 10 minutes
every 0.5 seconds. While the display is flashing after setting, press the CLOCK button again to confirm the setting and then
will constantly display.
… 75 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Wilfa Trysil Floor Comfort at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Wilfa Trysil Floor Comfort in the language / languages: English, Danish, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 20.25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info