727496
13
Zoom out
Zoom in
Previous page
1/20
Next page
13 | P a g e
DEHUMIDIFYING MODE
In this mode, the air conditioner only dehumidifies the room, the compressor will activate
intermittently depending on the ambient temperature. To activate this function mode, press
the Mode Control button until the indicator comes on. When the dehumidifying mode is
set, the orange light on the front panel comes on.
Please note that when switching function mode, there will be an approximately 3 minute
transition time. In dehumidifying mode, the exhaust hose does not need to be vented. If the
exhaust hose is vented, the room will be cooled as it dehumidifies. To prevent cooling,
remove the exhaust hose from the window kit and allow the warm air from the rear to be re-
circulated into the room. If room temperature is higher than 77°F, the fan speed can be
adjusted. If room temperature is lower than 77°F, the fan speed is set at Low.
NOTE: When using dehumidifying mode, venting the exhaust hose to the outside is not
required. If vented, the warm air is exhausted to the outside and cooling within the room may
occur. Additionally, if the exhaust hose is not vented, the unit may require more frequent
draining. The air conditioner does not have a humidistat in which a specific humidity level
can be set.
FAN ONLY MODE
In this mode, only the fan of the air conditioner runs and circulates the air in the room. To
activate this function mode, press the Mode Control button until the indicator comes on.
When the fan only mode is set, the green light on the front panel comes on.
In this function mode, the temperature cannot be set. Subsequently, set the desired fan
speed by pressing the Fan Speed button. Fan Only mode requires that the exhaust hose be
removed.
NOTE: The unit does not require venting in Fan Only mode.
AUTOMATIC MODE
When you set the air conditioner in AUTOMATIC mode, it will automatically select cooling or
fan only operation between 77 - 85F depending on the ambient temperature. The fan speed
is automatically selected and cannot be changed and the temperature cannot be set.
To activate this function mode, press the Mode Control button until the indicator comes
on. When the automatic mode is set, the light on the front panel displays the color of the
mode that the unit is currently operating in.
NOTE: In Automatic mode, hot air is exhausted from the outdoor exhaust port and the
exhaust hose must be connected to exhaust out the hot air.
FAN SPEED CONTROL
To set the fan speed, press the fan speed control button. Fan speed can be set at
Automatic, High, Medium and Low.
CLOCK
To set the clock, press and hold the clock button for 3 seconds. Press the up or down
buttons to set the current time. To save the current time, press and hold the clock button
again for 3 seconds.
TIMER (DELAYED SWITCH ON / OFF) FUNCTION
This function mode enables a delayed switch ON or delayed switch OFF of the air
conditioner. The time (hours) delay can be set, enabled and disabled. The timer is
adjustable between 1-24 hours.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Whynter ARC-110WD at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Whynter ARC-110WD in the language / languages: English as an attachment in your email.

The manual is 2,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info