727493

Whynter ARC-101CW Manual

10
Zoom out
Zoom in
Previous page
1/18
Next page
10
INSTALLATION
LOCATION
The air conditioner should be placed on a hard and level surface strong enough to support the unit. The unit has
casters and it should only be rolled on smooth, flat surfaces. Use caution when rolling on carpet surfaces. Do not
attempt to roll the unit over objects. Never place any obstacles around the air inlet or outlet and allow at least 20
inch of clearance for efficient air-conditioning.
EXHAUST HOSE INSTALLATION
When using the air conditioner, the hot air from the exhaust hose must be exhausted out of the room to
complete the air exchange of the condenser. When the unit is operating in dehumidifying or fan-only mode,
installation of the exhaust hose is optional.
1. Expand each end of the exhaust hose about 6”
2. Install the hose connectors onto the exhaust hose by turning
clockwise
3. Slide the slide locking hose connector onto the rear of the
unit (Fig. 3)
Only extend the both hoses to the necessary length. We do not recommend extending more than 9' long. If you are
interested in purchasing an additional 5’ exhaust hose, please contact support@whynter.com for retail sales infor-
mation.
WINDOW KIT INSTALLATION
The window kit has been designed to fit most standard vertical and horizontal windows (Fig. 4a and Fig. 4b).
However, it may be necessary to modify the installation procedures to accommodate your window.
NOTE:
• If your window opening is smaller than the minimum length of the window slider kit, the window slider kit can be cut
to fit the window opening. Never cut into the exhaust hose cut-out on the window slider kit.
• If your window opening is larger than the maximum length of the window slider kit, additional material will be
needed to cover the open space such as, Plexiglas, PVC plastic, ply wood, etc. Alternately, an additional window
slider kit can be purchased to be used in combination with the included kit.
• When using the window slider kit on a window or sliding door, additional security measures may be needed.
Fig. 3
Fig. 4a Fig. 4b
Fig. 4c
1. Open the window approximately 5”.
2. Adjust the length of the window slider to the same length and width of the opening of the window. Cut the window
slider if necessary to fit the length of your window.
3. Insert the fixture through the back grooved side of the window slider hose cut-out. Line up the fixture with the 4
screw holes and tighten the fixture with 4 screws from the front side of the slider panel. (Fig. 4c)
4. Fit the window slider kit into the window opening and close the window to secure the window slider kit. For 5.
long term installation, you may screw the window kit into your window frame.
5. Move the unit close to the window, extend the hose to the necessary length, keeping it as short and as straight as
possible and attach the other end of the hose to the window slider kit.
6. Align the tab cut-outs of the hose connector to the tabs on the fixture and snap the hose connector to the window
slider kit.
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Whynter ARC-101CW at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Whynter ARC-101CW in the language / languages: English as an attachment in your email.

The manual is 6,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info