484212
4
Zoom out
Zoom in
Previous page
1/12
Next page
P.06
P.07
Installation Instructions
3.Loosen the lock nut with a spanner and turn the foot by hand until it contacts the floor.
Hold the foot with one hand and fasten the nut against the cabinet with a spanner.
4.Press the four top corners again to check that the feet have been adjusted properly.
If the machine is still unstable repeat steps 2 and 3.
5.Put a solid cylinder (e.g. pop can) on the top cover of the washing machine in the left,
right, front and back positions. If it rolls then the machine is not level. The rolling direction
is the direction of the ground surface. The two legs in this direction need to be raised
at the same time until the washing machine is level. Once the machine is level ensure
that all the nuts are locked tight.
Connect the inlet pipe as indicated in the figure.
This machine only has a cold water inlet.
The water inlet pipe should be connected to
a ¾” threaded water tap
1. Connect the end of the pipe, with an elbow,
to the water inlet valve on the rear of the machine.
Tighten the nut clockwise.
2. Connect the other end of the inlet pipe to the
water tap.
Turn on the tap and ensure that there is no water
leakage.
There are three possible ways to connect the outlet hose to a suitable drain.
1. Position the outlet hose into a sink.
Inlet Pipe Connection
Installing the Inlet Pipe
Installing the Outlet Hose
Unpacking the Washing Machine
Unpack the washing machine and check that there is no transport damage.
Ensure that all the items (as shown on page 5) are included in the enclosed bag.
If there is any damage to the washing machine during transportation or any items
are missing, please contact your retailer immediately.
The packaging materials of this machine may be dangerous to children.
Please dispose of them properly in accordance with the local regulations.
Please do not throw the packaging materials away with general household waste.
Before using the washing machine the transport bolts
must be removed from the rear of the machine.
Please take the following steps to remove the bolts:
1. Loosen all 4 bolts with a spanner and remove them.
2. Stop the holes with the transport hole plugs provided.
3. Keep the transport bolts for future use.
The washing machine must be installed in a location with the following characteristics:
-Rigid, dry and level surface (if not level please refer to the following section “Adjusting the Feet”)
-Avoid direct sunlight
-Room temperature above 0°C
-Away from sources of heat
Ensure that the washing machine is not standing on the power cord.
Do not install the washing machine on a carpeted floor.
1.When positioning the washing machine please check
that all the feet are fully screwed into the cabinet. If not,
please turn them to their original positions and tighten
the nuts with a spanner.
2.After positioning the washing machine, press all four
corners on the top of the washing machine in sequence.
If the washing machine is not stable when being pressed,
this foot should be adjusted.
Disposal of the Packaging Materials
Removing the Transport Bolts
Selecting the Location
Adjusting the Feet
Installation Instructions
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for White Knight WM126M at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of White Knight WM126M in the language / languages: English as an attachment in your email.

The manual is 0,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info