484229

White Knight 44AW Manual

4
Zoom out
Zoom in
Previous page
1/8
Next page
OPERATION
Open the door.
Load clothes loosely into the drum.
Load sheets first, starting with one corner.
Close the door.
Dry your hands.
Check that the timer is in the ‘0’position.
Plug in the machine.
Select correct heat position, (see programme chart on control panel for recommendations).
Set the timer to the required time setting (see programme chart on control panel for recommendations).
For energy labeling purposes (EN61121:2005) for a cotton dry load, use the maximum load weight for
cotton and set the timer to the recommended drying time for cotton dry as specified on the control panel.
Press the start button if fitted.
The drum will begin rotating. Reversing drum models will stop periodically to rotate in the reverse
direction for a short time.
Should the clothes become dry before the cycle has finished, or if an excessive programme time has been
selected, the drum will continue to rotate while the thermostat will automatically regulate the heater to
reduce the risk of over drying.
If the door is opened during a cycle the dryer will stop. To restart, close the door and press the start button
(if fitted).When drying large items such as sheets, we suggest you periodically stop the dryer to
redistribute the load.
There is an automatic 12 minute cool down period at the end of every cycle, during which the heater is
switched off. This helps to minimize creasing, and must always be used fully to avoid the risk of fire.
NEVER SWITCH THE DRYER OFF AND LEAVE A HOT LOAD IN THE DRUM. RISK OF
FIRE.
ALWAYS CLEAN THE FILTER AFTER EACH USE. Failure to do so could cause the safety cut-out
to operate.
ANY PROBLEMS
If the clothes are not dry after normal drying time:
–Check that you used the correct heat setting.
–Check that you have not set the timer within a cool down period.
–Check that the lint filter has been cleaned. A blocked filter will restrict the airflow.
–Check that your dryer is heating - below the door to the left side, should feel warm to the touch after the
first 10-15 minutes of its programme.
Failure to heat may indicate the safety cut-out has operated. To reset, simply press the red button at the
rear of the machine. If it has operated then a sharp “click” will be heard.
This cut-out only operates if the airflow is severely restricted so make sure the filter is clean, the air inlets
and outlets at the front and back are not blocked, and that all other restrictions are removed before re-
starting.
- Pull the filter upwards and away from the appliance.
- Remove any threads or fluff by hand or with a soft brush.
- Slide the filter back.
- Wash the filter occasionally in detergent solution using a soft brush to
remove small particles.
- If your filter becomes damaged, replace it to ensure no damage is caused to
the dryer.
4


Need help? Post your question in this forum.

Forumrules
1

Forum

white-knight-44aw

Reset search

  • Bought as seen from a card in the coop.
    Can I stop a cycle to retrieve something early? Submitted on 29-1-2021 at 15:52

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for White Knight 44AW at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of White Knight 44AW in the language / languages: English as an attachment in your email.

The manual is 0,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info