702377
3
Zoom out
Zoom in
Previous page
1/5
Next page
MAINTENANCE OF THE CHARCOAL FILTER (FOR FILTRATION
MODELS ONLY)
This lter retains the unpleasant odours produced during cooking.
Replace the carbon lter every 4 months.
Fitting or replacing the carbon lter
1. Disconnect the hood from the mains.
2. Open and remove the extractor panel from its housing.
3. Remove the grease lters.
4. Fit one carbon lter on each side, covering both protective grilles
for the motor impeller.
Turn the lters clockwise to secure them to the central pins.
Proceed in reverse order to remove.
Ret the grease lters and extractor panel.
REPLACING THE LAMPS
The hood is equipped with an LED lighting system.
LEDs ensure excellent illumination, have a service life up to 10 times
longer than traditional bulbs, and oer up to 90% energy savings.
Note: For replacement LED, please contact the Technical After-sales Service
Centre.
WIFI MANUAL
LIVE APPLICATION REMOTE CONTROL /SET UP PROCEDURE
The LIVE feature allows to operate and supervise the appliance
remotely by external device. To enable the appliance to be remotely
controlled, you rst have to complete successfully the connectivity set
up process. This process is necessary to register your appliance and
connect to your home network. The set up procedure has to be carried
out only once. You have to carry it out again if you change your router
set up properties (network name or password or data provider).
1.1 BEFORE STARTING THE SET UP PROCESS
1. To use this feature You need to own: • a smart phone running
Android 4.3 (or higher) with a 1280x720 (or higher) screen or a
tablet or a smart phone running iOS 8 (or higher); • a wireless
router 2.4Ghz WiFi b/g/n connected to internet (verify with your
smart device that the signal strength of your home wireless
network close to the appliance is good).
2. Download & Install the free application: LIVE on your Android
smart-phone or iPAD/iPhone from the store. The App will guide
you, step by step, through the installation process.
If You do not have an account already, create one and subscribe (legal
terms) to service to be able to benet the features provided through
the app.
3. Register your appliance following the App instructions. For the
registration process You will need the Smart Appliance IDentier
(SAID) number, sticker on the appliance. The SAID is composed
by numbers and letters (10 chars ). You can take a note of your
appliance SAID here:
SAID … … … … … … … … … …
1.2 PROVISIONING
Before starting the installation process turn on your router and
verify that the wireless signal of your home router is reaching
the appliance. To verify the Wi strength signal use a Tablet or
Smart-phone connected only to the Wi-Fi router, disable any other
data connections, and place the device close to the appliance.
Open any internet web page in a browser and check that it is
downloaded fast correctly. If the internet connection of your
home is working correctly but the page is not downloaded, you
may need to install a Wi-Fi extender device (not provided with the
appliance).
If your router supports WPS 2.0 (or gather ) , follow one of the two
manual setup procedures to connect your appliance to router.
If your router is not supported by WPS, follow the manual setup
procedure .
Follow the instructions on your 6th Sense Live application on your
smartphone to connect the appliance to your wi network.
Otherwise read the next paragraphs for automatic or manual
connection.
1.2.1 AUTOMATIC SETUP INSTRUCTION FIRST TIME USE  WPS
METHOD
This procedure is applicable only if your router supports WPS2.0 (or
greater)
1. On your appliance activate the provisioning process by pressing
and hold for three seconds the connectivity button (an acoustical
feedback is played). The appliance is being set to a “search” mode
for a local network. The Connectivity icon on the appliance starts
blinking fast.
2. On wireless router press the WPS button to establish a connection
between the two products. An indicator light on your router will
begin blinking.
3. When the appliance successfully connects to the local router, the
wi icon switches from fast to slow blinking (supported not in all
appliances).
4. The appliance try to connect to Backend system. Connectivity
icon becomes steady. If the wi icon does not stop blinking after
few minutes, then the appliance has failed to nd the connections
to home network using WPS. Try the procedure again and if not
successful, then use one of the two manual setup instructions.
5. You can abort the WiFi connection procedure by pressing the
connectivity button.
1.2.2 MANUAL SETUP INSTRUCTION FIRST TIME USE  SCAN TO
CONNECT METHOD
This procedure uses the QR Code applied on the WiFi Label and is
applicable if Your router does not support WPS.
1. Turn ON your router and make sure the Internet connections is
working.
2. On your appliance activate the provisioning process by pressing
the connectivity button (one acoustical feedback is played) • you
should see the wi icon blinking on appliance HMI.
3. Turn ON your smart device (Phone or Tablet) and follow the
instruction on the app.
4. The wi icon on the appliance should stop blinking and turn ON
permanently once connected.
5. The setup process is complete.
6. You can abort the WiFi connection procedure by pressing the
connectivity button.
1.2.3 MANUAL SETUP INSTRUCTION FIRST TIME USE  UACCESS
POINT METHOD
This procedure uses the Micro Access Point technology and is
applicable if Your router does not support WPS.
1. Before starting the setup procedure please take note of the home
wireless network name (SSID), its PASSWORD and the SAID of
appliance. They will be required during the installation process.
2. Turn ON your router and make sure the Internet connections is
working.
3. On your appliance activate the provisioning process by pressing
and hold for 5 seconds the connectivity button (two acoustical
feedbacks are played, one after 3 seconds, one after 5 seconds) •
you should see the wi icon blinking on appliance HMI.
4. Turn ON your smart device (Phone or Tablet), access your list of
available wireless networks in the setting menu.
5. The appliance has created a wireless network (SSID), then select
it from the list of available wireless networks. The network name
is made up of the prex depending from your appliance type
(washer, dryer, …) followed by the MAC address (ex. VENTIL_88_
E7_12_xx_yy_ zz). If you don’t see it, you may need to refresh the
list of networks or verify the wi icon is on on the product display.
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Whirlpool WHVS90F at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Whirlpool WHVS90F in the language / languages: English as an attachment in your email.

The manual is 0,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Whirlpool WHVS90F

Whirlpool WHVS90F User Manual - German - 5 pages

Whirlpool WHVS90F User Manual - Dutch - 5 pages

Whirlpool WHVS90F User Manual - French - 5 pages

Whirlpool WHVS90F User Manual - Spanish - 5 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info