793899
4
Zoom out
Zoom in
Previous page
1/4
Next page
THANK YOU FOR BUYING A WHIRLPOOL PRODUCT.
In order to receive a more complete assistance, please
register your product on www.whirlpool.eu/register
Policies, standard documentation, ordering of spare parts and additional product information can be
found by:
Visiting our website docs.whirlpool.eu and parts-selfservice.whirlpool.com
Using QR Code
Alternatively, contact our After-sales Service (See phone number in the warranty booklet). When
contacting our After-sales Service, please state the codes provided on your product’s identifi cation plate.
EN
Quick guide
Before using the appliance carefully read the Safety
Instruction.
xxxxxxxxxxxx
xxxx
TROUBLESHOOTING EN
Before contacting the After-sales Service, refer to the table below. Often the malfunctions are minor and can be solved in few
minutes.
Malfunction
Solution
The tumble
dryer does not
turn on.
Insert the plug into the socket.
The plug is faulty.
Try to plug another appliance in the same socket. Do not use
connecting electrical devices to the socket, such as adapters or
extensions.
A power failure occurred. Wait for the power supply to be restored and switch the fuse on again
if necessary.
The tumble
dryer does not
start.
Close the door.
A time delay was set to the start of the cycle. For machines equipped with this function: wait for the set delay to
end or switch the machine off to reset it. Refer to the Options section.
The "Start/Pause" button was not pressed in
Press the "Start/Pause" button.
The Key Lock function was enabled (for
machines equipped with this option).
Refer to the Options section. If Key Lock was selected, disable it.
Switching the machine off will not disable this option.
Garments are
wet at cycle
completion.
Small load.
The automatic programme has not sensed the required fi nal moisture
so that the dryer completes the programme and stops. If this happens
simply select an additional short period of drying or select Extra Dry
option if available.
Large loads or heavier fabrics. Dryness levels can be modifi ed to the specifi c dryness desired.
Extra Dry is recommended for ready to wear items.
The drying
times are very
long.
An appropriate maintenance was not carried
out.
Refer to the Care & Maintenace section and perform the operations
described.
The programme, the time and/or the drying
level set are not suitable for the type and the
Refer to Programmes and Options sections to fi nd the programme
and options most suitable for the type of load.
The garments are too wet. Carry out a washing cycle with higher spin speed to remove as much
water as possible.
The dryer may be overloaded. Refer to the Programmes section to check the max load for each
programme.
Room temperature. The drying time may be longer if the room temperature falls outside
the 14–30°C range.
The programme
did not end. A power failure occurred might have occurred. In case of power failure, it is necessary to press the "Start/Pause"
button to restart the cycle.
Lights on or  ashing
Water tank The water tank is full. Empty the water tank. Refer to the Care & Maintenance section.
Door  lter Failure of the air fl ow necessary for machine
operation.
Clean the door fi lter and check whether air intake is free. Carrying
out these operations improperly may cause damages. Refer to Care &
Maintenance section.
Bottom  lter* The bottom fi lter requires cleaning. Clean the bottom fi lter. Refer to Care & Maintenance section.
DEMO
The cycle lasts
few minutes.
The dryer is in DEMO mode. The DEMO
indicator is on.
Disable the DEMO mode. The following actions must be carried out
in sequence, without breaks. Switch the machine on and then switch
it off again. Press the "Start/Pause" button until the buzzer is heard.
Switch the machine on again. The machine signals that the function
was disabled.
The presence
of wrench
symbol signals a
malfunction.
The machine sensors detected a failure.
Switch the dryer off and unplug it. Open the door immediately and
pull laundry out, to allow the heat to dissipate. Wait for about 15
minutes. Reconnect the dryer to the power supply, load the laundry
and restart the drying cycle. If the problem still occurs, contact
the After-Sales Service Centre and communicate the letters and
digits  ashing on the display.
For instance: F3 and E2.
*Note: some models are auto-cleaning and not equipped with bottom fi lter. Please refer to the Care & Maintenance section.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Whirlpool W6D84WB BE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Whirlpool W6D84WB BE in the language / languages: English as an attachment in your email.

The manual is 2.44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Whirlpool W6D84WB BE

Whirlpool W6D84WB BE User Manual - German - 4 pages

Whirlpool W6D84WB BE User Manual - Dutch - 4 pages

Whirlpool W6D84WB BE User Manual - French - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info