Load the machine, close the drum doors and check that
they are properly locked.
2. Add detergent and eventual additives as described on
the front page and in your Instructions for Use.
3. Close the lid.
4. Turn the programme selector to the desired
programme and temperature. The lamp next to the
“Start/Pause” button blinks. The indication lamp of
the predefined spin speed lights up. If you do not start
the programe soon after having made your choice,
the washing machine will switch off automatically after
about a quarter of an hour. Switch on the washing
machine again by turning the programe selector back to
“O” and then to the desired programe.
SELECT ANY DESIRED OPTION
Push the button(s) of any option(s) desired - the respective
indication lights up. When the combination of programme
and additional option(s) is not possible, the indication lights
switch off automatically. Unsuitable combinations of options
are deselected automatically.
“Colours 15°” button
•Saves energy used for water heating while maintaining a
good wash result.
•Supports colour maintenance when washing coloured
laundry.
•Recommendable for lightly soiled laundry without stains.
•Make sure that your detergent is suitable for cold wash
temperatures.
•Not selectable for Cotton 95°C.
“Fresh care” button
•Select this option if you cannot unload the laundry
soon after programme end, or if you tend to forget the
laundry in your washing machine. It will help to keep
your laundry fresh.
•The washing machine will start to tumble the laundry
periodically after programme end.
•The light of the “Fresh care” button will blink while this
function is active, and the display will show an animation.
•The periodic tumbling will last up to approximately
6 hours after the end of your wash programme, and
you can stop it at any time by pressing the “Fresh care”
button. It will last a while until you can open the door.
•After the “Fresh care” period has run out, the display
indicates “End”.
“Rapid” button
•Enables quicker washing by shortening the programme
duration.
•Recommendable for small loads or only lightly soiled
laundry.
“Prewash” button
•Only for heavily soiled loads (for example sand, granular
dirt). Increases the cycle time by approximately 15 min.
•Do not use liquid detergent for the main wash when
activating the Prewash option.
“Intensive rinse” button
•More water is added and rinse cycle is prolonged.
•This option is particularly suitable for areas with very
soft water, washing baby linen and helping people with
allergies.
“Spin” button
•Every programme has a predefined spin speed.
•Press the button to set another spin speed.
•If spin speed “0” is selected, the final spinning is
cancelled but intermediate spin peaks remain during the
rinse. The water is drained out only.
SAVE YOUR FAVOURITE PROGRAMMES
If there is a programme setting which you use frequently,
the appliance offers the possibility to save one setting for
each programme so that it can be used again by just pushing
one button.
•Select the desired programme, temperature, spin speed
and option(s), push and hold the “Favourites” button
for at least 3 seconds. The lamp next to “Favourites”
shortly flashes and then lights up - the programme
settings is saved.
Next time you want to use your individual programme
settings, select the programme, push the “Favourites”
button and start by pushing “Start/Pause”.
If you want to replace the saved programme setting
by another one:
•Select programme temperature, spin speed and options
as desired and then press and hold the “Favourites”
button for at least 3 seconds.The previously saved
programme setting will be replaced by the new one.
START DELAY
The “Start delay” button allows the user to run the machine
at his convenience, for example at night when electricity is
cheaper.
•Do not use liquid detergent when activating this function.
•Select programme, spin speed and options.
•Press the “Start delay” button several times to select a
delay time by 1 to 24 hours.
•Start the programme (see “Programme Start”). The
indication lamp over the “Start delay” button lights up
and goes off when the programme starts.
•Once having pressed the “Start/Pause” button,
the countdown of the time delay begins. The time
delay indication on the display disappears when the
programme starts and is replaced by the remaining time.
•After the “Start/Pause” button has been pressed,
the number of hours preselected can be reduced by
pressing again the “Start delay” button.
To cancel the “Start delay”
..before you press the “Start/Pause” button:
•Turn the programme selector to another position or
press the “Reset/Drain” button.
..after having pressed the “Start/Pause” button:
•Press the “Reset/Drain” button for at least 3 second.
The start delay indicator light goes off.
PROGRAMME START
Open the tap and press the “Start/Pause” button. The
indication lamp next to the “Start/Pause” button lights up.
The display shows the remaining programme time.
Due to variations in load and temperature of inlet
water, the remaining time is newly calculated in certain
programme phases. If this is the case, an animation
appears on the time display.
“LID OPEN” INDICATION
Before starting and after end of a programme, the lamp
lights to show the the lid can be opened. As long as a wash
programme is running, the lid remains locked and must
on no account be forced open. In case you have an urgent
need to open it during a running programme, refer to
“Cancel a running programme before the end”.
CHILD LOCK BUTTONS
You can lock the buttons of the control panel against
improper use (e.g. by children).
•Press both of the child lock buttons simultaneously and
hold them for at least 3 seconds. The key symbol on the
display lights up.
•To unlock the buttons again: proceed in the same way.
FAILURE INDICATIONS
In case of any failures or irregularities, consult the
“Troubleshooting Guide” in your Instructions for Use.
“Water tap closed”:
No or not sufficient inlet water.
“Service”:
Failure or malfunction of an electrical component.
“Clean pump”:
Waste water is not pumped out.
Spin speed on display blinks: unbalance during spinning
•
PROGRAMME END
The “Lid open” indicator lights up, and the display
shows “End”. After about a quarter of an hour, the
washing machine will switch off completely to save
energy.
1. Turn the programme selector to the “O” position.
2. Close the water tap.
3. Open lid and drum and unload the machine.
4. Leave the lid open for some time to allow the interior of
the machine to dry.
•
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
Press the “Start/Pause” button to pause the
programme. The light blinks.
•Select the new programme, temperature, any options
and another spin speed if you want.
•Press the “Start/Pause” button again. The new
programme continues at the same position where the
previous programme was interrupted. Do not add
detergent for this programme.
CANCEL A RUNNING PROGRAMME
BEFORE THE END
The “Reset/Drain” button cancels a programme before
the end.
•Press the “Reset/Drain” button for at least 3 seconds.
Any existing water is drained out before the door can
be opened.
CONSUMPTION DATA
Consumption values were measured in normalized conditions in compliance with standard IEC/EN 60 456. Consumption data in the home may vary with respect
to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.Water and energy consumption refer to the
default setting of the programmes; selecting special options or modifying spin speed or temperature will change the consumption data.
The programme duration may differ from the values indicated above as it depends on the operation conditions applicable at that time (see also
“Troubleshooting Guide” in your Instructions for Use).
* To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
** Standard Cotton programme and basis for Energy Label. For reasons of energy saving, the real water temperature may deviate from the declared cycle temperature.
*** After programme and spinning with maximum selectable spin speed, in default programme setting.
Power consumption in off-mode 0.11 W / in left-on mode 0.11 W
- the sensor technology adapts water, energy and programme duration to your wash load.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Whirlpool TDLR 60210 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Whirlpool TDLR 60210 in the language / languages: English as an attachment in your email.
The manual is 1,97 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
