528407
7
Zoom out
Zoom in
Previous page
1/13
Next page
Door seal
Dry the door seal after each washing with an
absorbent cotton cloth; make sure that the door
seal is completely dry before closing the door of
the empty washing machine.
Check the condition of the door seal periodically.
Filter
Check and clean the filter regularly, at least two
or three times a year (see “Draining Residual
Water/Cleaning The Filter”).
Do not use flammable fluids for cleaning
the appliance.
GB 7
Appliance exterior and control panel
Clean with a soft damp cloth.
If necessary, use some soapy water or a mild
neutral detergent (do not use detergents containing
solvents, abrasive detergents, window or general-
purpose cleaners - they may harm the surfaces).
Appliance interior
After each washing, leave the door open for some
time to allow the inside of the appliance to dry.
• If you never or seldom wash your laundry at
95°C, we recommend to occasionally run a 95°C
programme without laundry, adding a small
amount of detergent, to keep the interior of the
appliance clean.
CARE AND MAINTENANCE
Water inlet hose(s) (picture C, D or E - depending on
model)
Check the inlet hose regularly for brittleness and cracks and replace it
if necessary using a new hose of the same type.
The inlet hose as shown on picture “D” has a safety valve to prevent
the appliance against uncontrolled water inlet; if the safety valve
inspection window is red, the safety valve has been activated and the
hose must be exchanged. Contact out After-Sales Service or your
specialist dealer to obtain a new inlet hose. For unscrewing the inlet
hose as shown on picture “D”, you must push down the release lever
while unscrewing it.
If your inlet hose has a transparent hose coating (pict. “E”), periodically
check the colour of the transparent coating. If the transparent hose
shows a local dark colour change, this is an indication that the hose
may have a leak and should be replaced. Contact our After-Sales Service
team or specialist dealer to obtain a replacement hose.
Cleaning the mesh filter in the water inlet hose(s)
1. Close the tap and loosen the inlet hose on the tap.
2. Clean the internal mesh filter and screw the water inlet hose
back onto the tap.
3. Now unscrew the inlet hose on the rear of the washing machine.
4. Pull off the mesh filter from the washing machine connection
with universal pliers and clean it.
5. Refit the mesh filter and screw the inlet hose on again.
6. Turn on the tap and ensure that the connections are completely
water-tight.
Safety valve
inspection
window
C
D
E
Cleaning the detergent dispenser
1. Pull out the dispenser drawer until it stops.
Press with your finger on the space of the siphon being marked
with “PUSH” (picture “A”) to release the drawer and pull it out
completely.
2. Remove the siphon from the softener chamber by pulling it
upwards (picture “B”).
3. Wash all the parts under running water.
4. Clean the dispenser compartment with a damp cloth.
5. Refit the siphon in the softener chamber by pushing it down until
it stops; then push the dispenser drawer back into the dispenser
compartment.
A
B
PUSH
Release
lever
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Whirlpool Seattle 1400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Whirlpool Seattle 1400 in the language / languages: English as an attachment in your email.

The manual is 0,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Whirlpool Seattle 1400

Whirlpool Seattle 1400 User Manual - English - 2 pages

Whirlpool Seattle 1400 User Manual - German - 12 pages

Whirlpool Seattle 1400 Quick start guide - German - 2 pages

Whirlpool Seattle 1400 User Manual - Dutch - 12 pages

Whirlpool Seattle 1400 Quick start guide - Dutch - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info