Whirlpool is a registered trademark of Whirlpool USA
Add detergent as indicated on the front page and as described in
the chapter “Detergent and Additives” in your Instructions for Use
(remove separator in detergent dispenser for use of powder
detergent if necessary).
Turn the programme selector to the desired programme; the light
of the
“Start (Pause)”
button blinks. The
temperature
and
spin
speed
indicated on the display can be altered by pressing the
“Temperature” button or the “Variable spin” button.
When the combination of programme and additional option(s) is
not possible, the indication lights switch off automatically.
Unsuitable combinations of options are deselected automatically.
“Prewash” button
•Only for heavily soiled loads (for example sand, granular dirt)
sensible. Increases the cycle time by approximately 15 min.
•Do not use liquid detergent for the main wash when activating
the “Prewash” option.
“Eco” button
•With a modified temperature profile and a slightly prolonged
washing duration, the optimum combination of excellent washing
result and even lower energy consumption is achieved.
“Easy ironing” button
•Makes ironing easier by an increased water quantity and a very
gentle spin.
“Intensive rinse” button
•More water is added and rinse cycle is prolonged.
•This option is particularly suitable for areas with very soft water or
for washing baby linen, and helps people with allergies.
“Steam Stain Removal” button
•Treats the laundry with hot steam during the wash cycle in
order to help removing stains.
•Selectable for laundry made of cotton and/or synthetics within
temperature range of 40 to 60°C.
•If you select this option, “St” appears on the display during the
steam phases.
“Steam Sanitization” button
•Eliminates bacteria and helps sanitizing the laundry.
•Selectable for cotton and/or synthetic laundry items with care
label within temperature range of 40 to 60°C; do not load
more than 6kg cotton laundry when activating this option.
•Prolongs the programme by approximately half an hour to an
hour, depending on the load size.
•If you select this option, “St” appears on the display during the
steam phases.
“Variable spin” button (incl. “Rinse hold” )
•Every programme has a predefined spin speed.
•Press the button to set another spin speed.
•If spin speed “0” is selected, the final spinning is cancelled but
intermediate spin peaks remain during rinse. The water is
drained out only.
•If you select “Rinse hold” , the laundry remains in the last
rinse water without progressing to the final spin cycle, to avoid
creasing and prevent colours from changing. To activate the
“Rinse hold” press the “Variable spin” button repeatedly until
the “Rinse hold” symbol on the display lights up.
-The wash programme stops to “Rinse hold” when the
“Rinse hold” symbol on the display blinks; the light of
“Start (Pause)”
button blinks as well.
-To terminate the “Rinse hold” by draining the water,
without any spinning, press the
“Start (Pause)”
button.
-To terminate the programme by spinning the laundry, press the
“Variable spin” button to select the desired spin speed and then
“Start (Pause)”
to start the spin cycle.
-Do not leave the laundry to soak for too long in the “Rinse hold”.
If there is a programme setting which you use frequently, the
appliance offers the possibility to save one setting for each
programme so that it can be used again by just pushing one button.
CONSUMPTION DATA
Programme
Temperature
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approx. Programme Duration
(hours : minutes)
*
White Cotton / Antibacterial957.074
**
2.102:20
Cotton607.0691.332:10
Cotton with “Eco”
***
607.0541.192:20
Cotton407.0690.752:05
Synthetics603.546
**
0.851:35
Synthetics403.5420.501:20
Delicates302.5600.400:45
Wool402.0600.600:45
Handwash402.0450.600:40
Big Items403.0740.751:30
Steam Refresh—1.00.50.200:10
Steam Self-Sanitization——110.500:35
SuperEco607.0690.844:00
Daily load406.0730.601:00
Quick wash 30’306.0730.300:30
Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home may vary with respect
to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.
*The time indicated on the display can deviate from the values in the table, because it takes into account the operation conditions applicable at that time.
**To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
***Reference Programme for Energy Label (with separator in detergent dispenser removed for use of powder detergent).
ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME
SELECT ANY DESIRED OPTION
SAVE YOUR FAVOURITE PROGRAMMES
•Select the desired programme, temperature, spin speed and
option(s), push and hold the
“Favourites”
button for at
least 3 seconds. The lamp of the
“Favourites”
button
shortly blinks and then lights up - the programme setting is saved.
Next time you want to use your individual programme setting,
select the programme,
shortly
push the
“Favourites”
button
and start by pushing
“Start (Pause)”
.
If you want to replace the saved programme setting by another
one, proceed as already described above.
The “Start delay” allows to run the machine at the consumer’s
convenience, for example at night when electricity is cheaper. Do
not use liquid detergent when activating the “Start delay”.
•Select programme, temperature, spin speed and options.
•Press the Start delay button to select one of the delay time
steps between 0:30 and 23:00 hours.
•Press the
“Start (Pause)”
button; the light stops blinking and
becomes solid.
The countdown of the delay time begins; the clock symbol next to
the delay time and the colon between hours and minutes blink.
•The time delay indication disappears when the programme
starts and it is replaced by the remaining programme time.
To cancel the “Start delay”
..before you press the “Start (Pause)” button:
•Press the
“Reset/Drain”
button, or set the start delay time to
“0:00” - the delay time disappears after a few seconds.
..after having pressed the “Start (Pause)” button:
Press the
“Start (Pause)”
button - the delay time disappears from
the display; press
“Start (Pause)”
again to start the selected
programme immediately.
Before starting a programme, the symbol lights to show that the
door can be opened to add more washing. As soon as you press
“Start (Pause)”
, the door will lock until the end of the
programme and must on no account be forced open. In case you
have to open it urgently during a running programme, refer to
“Reset a running programme before the end”.
If you try to start a wash programme and the door is not properly
closed, the “Add garment” indication will blink.
Open the tap and press the
“Start (Pause)”
button; the blinking
“Start (Pause)”
button light becomes constant. The “Add
garment” indication goes out, and the lit bubbles indicate that the
programme is in process. In some phases, the remaining
programme time is newly calculated - if this is the case, the “6
th
sense” indication on the display will fade, and the remaining
programme time is replaced by an animation.
Activating the child lock prevents children from starting a wash
cycle or changing the settings of a running programme. The child
lock cannot be activated or deactivated when the programme
selector is in the “Off/O” position. To activate the child lock:
•Turn the programme selector to a programme position, or run
a programme as usual.
•Press the “Temperature” and the “Variable spin” button
simultaneously for at least 3 seconds. The “Child lock” symbol
will shortly blink and then light up to indicate that the
child lock is active.
The programme setting cannot be changed anymore; the only change
possible is to switch the washer off by turning the programme selector
to the “Off/O” position. To deactivate the child lock, proceed in the
same way as for activating it.
If one of the red failure indications on the display lights up, refer to
the “Troubleshooting Guide” in your “Instructions for Use”.
•The display shows “End”, and the “Programme finished”
indication lights up.
1.Turn the programme selector to the “Off/O” position.
2.Close the water tap.
3.Open the door and unload the machine.
•Leave the door ajar to allow the drum to dry.
•If you do not turn the programme selector to the “Off/O”
position, all lights of the control panel go out after a few
minutes to save energy - only “End” will remain on the display.
The symbol will light up at the end of the programme if you used
too much detergent. Use less detergent next time. If the symbol
lights up and the display shows “Fod”, too much foam interrupted
the wash process; refer to the “Troubleshooting Guide” in your
Instructions for Use.
1.Press the
“Start (Pause)”
button to pause the programme.
The light blinks.
2.Select the new programme, temperature, any options and
another spin speed if you want.
3.Press the
“Start (Pause)”
button again. The new programme
continues at the same position where the previous programme was
interrupted. Do not add detergent for this programme.
The
“Reset/Drain”
button cancels a programme before the end.
•Press the
“Reset/Drain”
button for at least 3 seconds; an
animation appears on the display. Any existing water is drained
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Whirlpool pure steam at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Whirlpool pure steam in the language / languages: English as an attachment in your email.
The manual is 0,84 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
