Whirlpool is a registered trademark of Whirlpool USA
Load your laundry, close the door properly and add detergent as
indicated on the front page and as described in the chapter “Detergent
and Additives” in your Instructions for Use (remove separator in
detergent dispenser for use of powder detergent if necessary).
1.Turn the
programme selector
to the desired programme.
The display shows the programme duration in hours and
minutes as well as the predefined temperature. The
“Start
(Pause)”
button blinks.
2.The
temperature
can be altered by pressing the
“Temperature” button.
3.The indication lamp of the predefined
spin speed
lights up. In
case you want to set another spin speed, press the “Spin
speed” button.
Push the button(s) of any option(s) desired - the respective
indication lights up.
When the combination of programme and option is not possible,
the lights switch off automatically. Unsuitable combinations of
options are deselected automatically.
“Prewash” button
•Only for heavily soiled loads (for example sand, granular dirt).
Increases the cycle time by approximately 15 min.
•Do not use liquid detergent for the main wash when activating
the Prewash option.
“Eco” button
•With a modified temperature profile and a prolonged washing
duration, the optimum combination of good washing result and
lower energy consumption is achieved.
“Easy ironing” button
•Reduces creasing by an increased water quantity and a very gentle spin.
“Intensive rinse” button
•More water is added and rinse cycle is prolonged.
•This option is particularly suitable for areas with very soft
water, washing baby linen and helping people with allergies.
“Spin speed” button (incl. “Rinse hold” )
•Every programme has a predefined spin speed.
•Press the button to set another spin speed.
•If you select spin speed “0”, the final spinning is cancelled, and
the water is drained out only. However, intermediate spin
phases remain during rinse.
•If you select
“Rinse hold”
, the laundry remains in the
last rinse water without progressing to the final spin cycle to
avoid creasing and prevent colours from changing.
-Select
“Rinse hold”
if you want to postpone spinning to a
later time or if you want to drain only.
-Do not leave the laundry to soak in the rinse hold for too long.
-The programme stops to “Rinse hold” when the “Rinse
hold” light in the programme sequence indicator is
on. The
“Start (Pause)”
button
light blinks.
-To terminate the “Rinse hold” by draining the water, without
any spinning, press the
“Start (Pause)”
button
.
-To terminate the programme by spinning the laundry, press the
“Spin speed” button to select the desired spin speed and then
the
“Start (Pause)”
button to start the spin cycle.
CONSUMPTION DATA
Programme
Temperature
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approx. Programme Duration
(hours : minutes)
*
Mixed406.0730.601:00
Cotton958.082
**
2.402:10
Cotton
***
608.0591.362:20
Cotton408.0770.75
2:05
Synthetics603.546
**
0.851:35
Synthetics403.5420.50
1:20
Delicates302.5600.40
0:45
Wool/Handwash402.0450.600:40
White408.0770.852:21
Light colours405.5700.50
1:20
Dark405.0450.60
1:40
SuperEco608.0750.95
4:00
AquaEco403.0190.451:00
Speed 15303.0300.20
0:15
Bedlinen603.5601.30
2:00
Big Items403.0740.751:30
Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home may vary with respect
to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.
*The time indicated on the display can deviate from the values in the table, because it takes into account the operation conditions applicable at that time.
**To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
***Reference Programme for Energy Label (with separator in detergent dispenser removed for use of powder detergent).
ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME
SELECT ANY DESIRED OPTION
The “Start delay” allows to run the machine at the consumer’s
convenience, for example at night when electricity is cheaper. Do
not use liquid detergent when activating the “Start delay”.
•Select programme, temperature and options.
•Press the “Start delay” button to select a delay time up to 23
hours. The light of the
“Start (Pause)”
button blinks.
•Press the
“Start (Pause)”
button . The countdown of
the delay time begins. The light of the
“Start (Pause)”
button
is on. The light of the start delay button will keep blinking
until the programme starts.
•As soon as the programme starts, the start delay on the display
is replaced by the remaining programme time, and the light of
the “Start delay” button goes off.
•Once having pressed the
“Start (Pause)”
button, the
number of hours preselected can be changed by pressing and
holding the “Start delay” button.
To cancel the “Start delay”
...before you press “Start (Pause)”:
•Turn the programme selector to another position or press the
“Reset/Drain”
button .
...after having pressed “Start (Pause)”:
•Press
“Start (Pause)”
- the delay time disappears from
the display. Press
“Start (Pause)”
again to start the
selected programme immediately.
Open the tap and press
“Start (Pause)”
. The light stops
blinking and is on. The programme sequence indicator shows the
current programme phase, running from left to right through
Wash, Rinse, Spin/Drain.
The display shows the remaining programme time. Due to
variations in load and temperature of inlet water, the remaining
time is newly calculated in certain programme phases. If this is the
case,
an animation appears on the display
.
Activating the child lock prevents children from starting a wash
cycle or changing the settings of a running programme. The child
lock cannot be activated or deactivated when the programme
selector is in the “Off/O” position. To activate the child lock:
•Turn the programme selector to a programme position, or run
a programme as usual.
•Press the 2 buttons marked with the key symbol
simultaneously for at least 3 seconds. A key-like symbol will shortly
appear on the display to indicate that the child lock is active.
Any time you try to change a programme setting with active child
lock, the display will briefly show the key-like symbol. The
programme setting cannot be changed anymore. The only change
possible is to switch the washer off by turning the programme
selector to the “Off/O” position. To deactivate the child lock:
•Press again the 2 buttons marked with the key symbol
simultaneously for at least 3 seconds.
Before starting and after end of a programme, the lamp lights to show
that the door can be opened. As long as a wash programme is running,
the door remains locked and must on no account be forced open. In
case you have an urgent need to open it during a running programme,
refer to “Reset a running programme before the end”.
“Service”
Lighting up of the “Service” indication can be caused by a fault in an
electrical component. Refer to the “Troubleshooting Guide” in your
Instructions for Use. If the fault persists, contact our After Sales Service.
“Water tap closed”
The appliance has no or insufficient water supply. Open the water
tap. If the indication still lights up, refer to the “Troubleshooting
Guide” in the Instructions for Use.
“Clean pump”
Waste water is not pumped out. Check whether the drain hose is
kinked or the filter must be cleaned. In the latter case refer to the
Instructions for Use (“Removing the Filter”).
•The display shows “End” and the “Door open” indication lights.
1.Turn the programme selector to the “Off/O” position.
2.Close the water tap.
3.Open the door and unload the machine.
4.Leave the door ajar to allow the drum to dry.
1.Press
“Start (Pause)”
to pause the programme. The
light blinks.
2.Select the new programme, temperature, any options and
another spin speed if you want.
3.Press
“Start (Pause)”
again. The light is on, and the
programme continues at the same position where the
previous programme was interrupted. Do not add detergent
for this programme.
The
“Reset/Drain”
button cancels a programme before
the end.
•Press the
“Reset/Drain”
button for at least 3
seconds. “rES” appears on the display. The water is drained
out; it may last a while until you can open the door.
START DELAY
PROGRAMME START
CHILD LOCK
“DOOR OPEN” INDICATION
RED INDICATIONS
PROGRAMME END
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
RESET A RUNNING PROGRAMME BEFORE
THE END
The Sensor Technology automatically adapts Programme Time, Wa
ter and Energy consumption to the size of your wash load.
30106424GB.fm Page 2 Friday, October 1, 2010 2:58 PM
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Whirlpool Pure 1000 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Whirlpool Pure 1000 in the language / languages: English as an attachment in your email.
The manual is 1,15 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
