75504
12
Zoom out
Zoom in
Previous page
1/14
Next page
GB 12
Red indication
lights up
(if fitted on your
machine)
Indication on
time display
(if fitted on your
machine)
Description
Causes
Solutions
“Service”
from “F02” to “F35”
(except “F09”)
“Electrical module fault”
Select and start the “Drain” programme or push the
“Reset” button for at least 3 seconds.
from “F40” to “F43” “Electrical module fault”
Make sure that the water tap is open. If yes:
Switch the washing machine off or turn the
programme selector to the “Off/O” position; then
switch it on again or turn the programme selector
to a wash programme. If there is still a failure:
Select and start the “Drain” programme or push
the "Reset" button for at least 3 seconds.
“F09” “Water level too high” (after programme
cancellation or false operating). Switch off the
appliance (by pressing the “On/Off” button or by
turning the programme selector to the “Off/O”
position - depending on the model) and then switch
it on again, select the programme “Drain” and start
within 15 sec.
“FA” “Waterstop fault”
Switch off the appliance the appliance (by pressing
the “On/Off” button or by turning the programme
selector to the “Off/O” position - depending on the
model), pull out mains plug and turn the water tap
off. Tilt the appliance forward carefully to allow
collected water to flow out from the bottom. Then:
Plug in the appliance again.
Turn the water tap on (if water immediately flows
into the appliance without the appliance being
started, there is a failure; turn off the tap and notify
the After-Sales Service).
Select and start the desired programme again.
“Fod” “Overfoaming”
Too much foam interrupted the wash programme.
Select and start the “Rinse & Spin” programme.
Afterwards select and start the desired
programme again, using less detergent.
If any of the faults described above persist,
unplug the appliance, turn off the water tap
and contact our After-Sales Service (see next
chapter).
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Whirlpool Montana 1400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Whirlpool Montana 1400 in the language / languages: English as an attachment in your email.

The manual is 0,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Whirlpool Montana 1400

Whirlpool Montana 1400 Quick start guide - English - 2 pages

Whirlpool Montana 1400 User Manual - English - 13 pages

Whirlpool Montana 1400 Quick start guide - German - 2 pages

Whirlpool Montana 1400 User Manual - German - 13 pages

Whirlpool Montana 1400 User Manual - Dutch - 2 pages

Whirlpool Montana 1400 User Manual - Dutch - 13 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info