Manual Whirlpool Miami 1400 (page 2 of 2) (English)

69466

Zoom out

Zoom in

1/2

5019 301 01029

Programme

Temperature

(°C)

Load

(kg)

Water

(l)

Energy

(kWh)

Approx. Programme

Duration

(hours : minutes)

Cotton 95 6.0 59 * 1.90 2:00

Cotton with “Eco”** 60 6.0 49 1.14 2:20

Cotton 40 5.0 56 0.70 2:00

Synthetics 60 2.5 50 * 0.80 1:35

Synthetics 40 2.5 46 0.50 1:20

Delicates 30 1.5 60 0.50

0:45

Daily load 40 3.0 41 0.50

1:00

Quick wash 30 3.0 41 0.40

0:30

Wool 40 1.0 60 0.50

0:45

Handwash 40 1.0 45 0.50

0:40

Handwash 30 1.0 45 0.40

0:36

CONSUMPTION DATA

Consumption values were measured in normalized conditions in compliance with standard IEC/EN 60 456. Consumption data

in the home may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load

and the type of wash.

* To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the

water out.

** Reference Programme for Energy Label.

ADD DETERGENTS, CLOSE THE DOOR AND

SELECT THE PROGRAMME

SELECT ANY DESIRED OPTION

“DOOR OPEN” INDICATION

Before starting and after end of a programme, the

lamp lights to show the the door can be opened.

As long as a wash programme is running, the door

remains locked and must on no account be forced

open. In case you have an urgent need to open it

during a running programme, refer to “Cancel (Reset)

a running programme before the end”.

RED INDICATIONS

“Service”

Lighting up of the “Service” indication can be caused

by a fault in an electrical component. Refer to the

“Troubleshooting Guide” in your “Instructions for

Use”; if the fault persists, contact our After Sales

Service.

“Water tap closed”

The appliance has no or insufficient water supply.

Open the water tap: if the indications still lights

up, refer to the “Troubleshooting Guide” in the

Instructions for Use.

“Clean pump”

Waste water is not pumped out. Check whether the

drain hose is kinked or the filter must be cleaned:

in the latter case refer to the Instructions for Use

(“Removing the Filter”).

PROGRAMME START

Open the tap and press the “Start/Pause” button.

The indication lamp next to the “Start/Pause”

button lights up. The programme sequence indicator

shows the current programme phase, running from

left to right through Wash, Rinse, Spin/Drain.

When the programme phase is finished, the

corresponding indication goes out.

PROGRAMME END

• All the lights of the programme sequence indicator

are off, and the “Door open” indication lights up.

1. Turn the programme selector to the “Off/O”

position.

2. Close the water tap.

3. Open the door and unload the machine.

4. Leave the door ajar to allow the drum to dry.

CHANGE PROGRAMME AND/OR OPTIONS

AFTER PROGRAMME START

1. Press the “Start/Pause” button to pause the

programme. The light flashes.

2. Select the new programme (with temperature),

any options and another spin speed if you want.

3. Press the “Start/Pause” button again. The new

programme continues at the same position where

the previous programme was interrupted. Do not

add detergent for this programme.

CANCEL (RESET) A RUNNING PROGRAMME

BEFORE THE END

The “Reset” button cancels a programme before

the end.

• Press the “Reset” button for at least 3 seconds.

Any existing water is drained out before the door

can be opened.

Whirlpool is a registered trademark of Whirlpool USA.

The “Start Delay” allows to run the machine at the

consumer’s convenience, for example at night when

electricity is cheaper. Do not use liquid detergent

when activating “Start delay” option.

• Select programme, temperature and options.

• Press the “Start Delay” button to select the delay

time by 1, 3, 6, 9 or 12 hours.

• Press the “Start/Pause” button.

The indication over to the “Start Delay” button

lights up and goes off when the programme

starts.

• Once having pressed the “Start/Pause” button,

the countdown of the time delay begins. When

the programme starts, the start delay indicator

light goes off and is replaced by the programme

sequence indication.

• After the “Start/Pause” button has been

pressed, the number of hours preselected can be

reduced by pressing again the “Start Delay”

button.

To cancel the “Start Delay”

..before you press the “Start/Pause” button:

• Turn the programme selector to another position

or press the “Reset” button.

..after having pressed the “Start/Pause” button:

• Press the “Reset” button for at least 3 seconds -

the start delay indicator light goes out.

START DELAY

Add detergent as indicated on the front page and as

described in the chapter “Detergent and Additives”

in your Instructions for Use.

Close the door and turn the programme selector

to the desired programme and temperature. The

indication lamp next to the “Start/Pause” button

blinks and the indication lamp of the predefined spin

speed lights up.

Push the button(s) of any option(s) desired - the

respective indication lamp lights up.

When the combination of programme and additional

option(s) is not possible, the indication lights switch

off automatically. Unsuitable combinations of options

are deselected automatically.

“Prewash” button

• Only for heavily soiled loads (for example sand,

granular dirt) sensible. Increases the cycle time by

approximately 15 min.

• Do not use liquid detergent for the main wash

when activating the Prewash option.

“Eco” button

• With a modified temperature profile and a slightly

prolonged washing duration, the optimum

combination of excellent washing result and even

lower energy consumption is achieved.

“Intensive rinse” button

• More water is added and rinse cycle is prolonged.

• This option is particularly suitable for areas with

very soft water, washing baby linen and helps

people with allergies.

“Rinse hold” button

• The laundry remains in the last rinse water

without pregressing to the final spin cycle to avoid

creasing and prevent colours from changing.

• This option is particularly recommended for the

programmes “Synthetics”, “Daily load” and

“Delicates”.

• It is particularly useful if you want to postpone

spinning to a later time, or if you want to drain

only.

• If you select “Rinse hold” do not leave items to

soak for too long.

Note: The programme stops to “Rinse hold” at the

time the “Rinse hold” lights in the preogramme

sequence indication is on. The indication lamp next

to the “Start/Pause” button flashes.

Terminate the “Rinse hold” option:

• Press the “Start/Pause” button; the programme

will terminate automatically with the final spin

cycle for the present wash programme.

• If you do not wish to spin the clothes, turn the

programme selector knob to the “Drain”

programme and press the “Start/Pause” button.

“Variable spin” button

• Every programme has a predefined spin speed.

• Press the button to set another spin speed.

• If spin speed “0” is selected, the final spinning is

cancelled but intermediate spin peaks remain during

the rinse. The water is drained out only.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Whirlpool Miami 1400 in the language / languages: English as an attachment in your email.

The manual is 0,65 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Whirlpool Miami 1400

Whirlpool Miami 1400 User Manual - English - 14 pages

Whirlpool Miami 1400 User Manual - English - 13 pages

Whirlpool Miami 1400 Quick start guide - German - 2 pages

Whirlpool Miami 1400 User Manual - German - 13 pages

Whirlpool Miami 1400 Quick start guide - Dutch - 2 pages

Whirlpool Miami 1400 User Manual - Dutch - 13 pages

Whirlpool Miami 1400 Quick start guide - French - 2 pages

Whirlpool Miami 1400 User Manual - French - 13 pages

Whirlpool Miami 1400 User Manual - Italian - 13 pages

Whirlpool Miami 1400 User Manual - Turkish - 13 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Whirlpool Miami 1400 Manual

Product: