Manual Whirlpool IVH840CNE (page 34 of 124) (English, German, Dutch, French, Italian)

757513

Zoom out

Zoom in

1/124

Instructions for assembly

2.8 Important notes for ﬁ tting

• The appliance must be handled and installed by two or

more persons - risk of injury. Use protective gloves to

unpack and install - risk of cuts.

• Keep children away from the installation site.

• After unpacking the appliance, make sure that it has

not been damaged during transport. In the event of

problems, contact the dealer or your nearest After-sales

Service.

• Once installed, packaging waste (plastic, styrofoam

parts etc.) must be stored out of reach of children - risk

of suﬀ ocation.

• The appliance must be disconnected from the power

supply before any installation operation - risk of

electrical shock. During installation, make sure the

appliance does not damage the power cable - risk of

ﬁ re or electrical shock. Only activate the appliance

when the installation has been completed.

• Carry out all cabinet cutting works before ﬁ tting the

appliance in the furniture and remove all wood chips

and sawdust.

• If the appliance is Not installed above an oven, a

separator panel (not included) must be installed in the

compartment under the appliance.

• The cross-section of wall vents and the cut-out in the

base panel should should at least correspond to the

exhaust air pipe. The outﬂ ow opening must be at least

500 cm². Reduce the height of the skirting boards or

make corresponding openings.

• When installing the appliance make sure that the con-

vection air unit is still accessible when the kitchen has

been completely installed. If necessary levelling feet for

the kitchen units must be moved.

• The hob fan can be operated in the extraction air and

recirculation air mode.

• Lead the outgoing air outside through a ventilation shaft

intended for this purpose or through the wall of the

building.

• Outgoing air may not be led into a smoke or exhaust

gas ﬂ ue which is in operation. Contact the district mas-

ter chimney sweep if you are in any doubt.

• A suﬃ cient supply of inlet air must be provided if a

wood, coal, gas or oil heater requiring a chimney is

operated in the environment of the hob fan, since an

insuﬃ cient supply of air results in a risk of poisoning.

The safe operation of the hob fan is guaranteed when

the negative pressure resulting from the hob fan does

not exceed 0.04 mbar (4 Pa) and a suﬃ cient supply of

inlet air can ﬂ ow into the room.

• Exhaust air pipes must comply with ﬁ re class B 1 DIN

4102. Please make sure that the minimum nominal

width of the appliance connecting pieces is not re-

duced.

• A system recommended for the airﬂ ow and compatib-

le with the hob extractor should always be used.

• The nominal width of the recirculation air pipe should

not be less than 150 mm.

• Exhaust air pipes should be as short as possible. They

should not have a 90-degree angle; instead they should

have soft bends and no reductions in their cross-secti-

on.

• Never use pipes with a diameter of less than 150 mm.

No bends/ angles may be laid 50 cm before the fan

module.

• Always insert a straight piece of approx. 50 cm bet-

ween two angles/bends.

Assembly

• Please observe the generally valid power plant and ﬁ re

authority requirements.

• Installation/connection by qualiﬁ ed staﬀ members

• No claims for damage caused by failure to observe

this document and/or the documents enclosed with the

appliance may be enforced against the manufacturer.

• Observe minimum clearances to walls: on the side at

least 100 mm and at the back at least 50 mm.

Preparing the table cut-out

• Mill around the cut-out or produce it with strips of wood.

• Cut-outs accurate to dimension and right-angled.

• Ensure the correct height, so that the hob and the ﬁ lter

unit ﬁ t exactly.

• Take recess ventilation of at least 400 cm2 into account

on the side.

• Units and covers must be temperature-resistant (<

75°C).

• Only plan for the ﬁ lter set to be on the left.

Installing the fan unit

• Place the unit (charcoal or plasma) into the niche.

• Align the air vents, fasten.

• Establish an electrical connection.

• Insert the hob, align.

• Do not operate the hob while the silicone is hardening.

• Test the primer/adhesive for usability before gluing.

• Do not screw the hob tight as it weighs 18 kg (ﬁ lter not

included).

• Combustible walls/ceilings above hobs must be ﬁ tted

with ﬁ re-resistant cladding according to the relevant ﬁ re

department organs.

Connecting to the electric power supply

• Only switch the safety fuses/main switch on once the

hob has been installed/wired.

• Mount the enclosed sign in a clearly visible position

since this will no longer be accessible after installation.

• Combustible walls/ceilings above hobs must be ﬁ tted

with ﬁ re-resistant cladding according to the relevant ﬁ re

department organs.

• Install the hob properly to ensure its protection against

accidental contact.

• The charcoal or plasma ﬁ lter must be installed so that it

is always conveniently and easily accessible for servi-

cing purposes.

PLEASE NOTE

When the convection air mode is in operati-

on, ventilation must be suﬃ cient in order for

the air humidity to be removed.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Whirlpool IVH840CNE in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 7,58 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Whirlpool IVH840CNE Manual

Product: