650640
3
Zoom out
Zoom in
Previous page
1/8
Next page
3
EN
Turn the knob to select the desired drying time. Conrm it
by pressing the knob.
Set dryness level, if needed
If you want to change the dryness level, make sure that the
Dryness level button « lights up.
Turn the knob to select the desired dryness level, then press
the knob to conrm.
Select options, if needed
If you want to select additional options, make sure that the
Options button « lights up. The options which are selectable
for your programme are indicated by lighting arrows.
Turn the knob to select the desired options. The symbol of
the selected option will blink. To conrm it, press the knob.
Some options / functions can be selected by directly
pressing the button.
Refer to section OPTIONS, FUNCTIONS AND
INDICATORS for more information.
INDIVIDUAL MODE
After you have switched on the dryer, you are not forced to
follow the GUIDED MODE.
It is up to you which order you choose to set your
programme. To do a setting, rst press the relevant button,
then turn the knob to select, and nally press the knob to
conrm.
The variety of options and dryness levels depends on the
programme selected. Therefore it is recommended to start
your setting with selecting the programme.
5. START PROGRAMME
Press and hold Start/Pause « until the button lights up
solidly; the drying process starts.
The duration can be recalculated and adapted in the course
of the programme.
During such phases, an animation occurs on the display.
6. CHANGE THE SETTINGS OF A RUNNING
PROGRAMME, IF NEEDED
You can still change some settings after a programme was
started:
• Adjust drying time (only if programme Drying time is
selected)
• Add or cancel an option, provided the progress of the
programme still allows it.
Press the relevant button. The selected setting will blink for
a few seconds.
While blinking, you can adjust the setting by turning the
knob. If the value or setting stopped blinking, press the
button again.
Press the knob to conrm the modication. If you do not
conrm, the modication will be conrmed automatically
— the modied setting will stop blinking.
The programme will continue automatically.
To change the settings of a running programme or start
delay, you can also:
• press Start/Pause to put the running programme on pause
• change your settings
• press Start/Pause again to continue the programme.
7. RESET A RUNNING PROGRAMME, IF NEEDED
Press and hold the On/O button « until “rES” appears on
the display.
The programme is ended afterwards.
Immediately open the door and unload the laundry, so that
eventual heat in the laundry can dissipate.
8. SWITCH OFF THE DRYER AFTER PROGRAMME END
At the end of the programme, „End“ appears on the
display. Press On/O « to switch o the dryer. Open the
door and take out your laundry.
The dryer will switch o automatically in about a quarter of
an hour after programme end, to save energy.
9. EMPTY WATER TANK / CLEAN DOOR FILTER /
CLEAN BOTTOM FILTER
Refer to section CARE AND MAINTENANCE.
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Whirlpool HSCX 10443 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Whirlpool HSCX 10443 in the language / languages: English as an attachment in your email.

The manual is 2,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Whirlpool HSCX 10443

Whirlpool HSCX 10443 Usermanual and installation guide - English - 43 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info