5019 301 06324
Whirlpool is a registered trademark of Whirlpool USA
Add detergent as indicated on the front page and as described in
the chapter “Detergent and Additives” in your Instructions for Use
(remove separator in detergent dispenser for use of powder
detergent if necessary). Turn the programme selector to the
desired programme; the light of the
“Start (Pause)”
button
blinks. The
temperature
and
spin speed
indicated on the display
can be altered by pressing the “Temperature” button or the
“Variable spin” button.
When the combination of programme and additional option(s) is
not possible, the indication lights switch o
Unsuitable combinations of options are deselected automatically.
“Prewas
• Only for heavilor example sand, granular dirt)
sensible. Increases the cycle time by approximately 15 min.
• Do not use liquid detergent for the main wash when
the “Prewash” option.
“Eco” button
• With a ofile and a prolonged washing
duration, the optimum combination of good washing result and
lower energy consumption is achieved.
“Easy ironing” button
• Makes ironing easier by an increased water quantity
gentle spin.
“Intensive rins
• More water is added and rinse cycle is prolonged.
• T
for washing baby linen, and helps people with allergies.
“
• Every programme has a prede
• Press the button to set another spin speed.
• If spin speed “0”
intermediate spin peaks remain during rinse. The water is
drained out only
• I
water without progressing to the final spin cycle, to avoid creasing
and prevent colours from changing. To activate the “Rinse hold”,
press the “Variable spin” button repeatedly unt
symbol on the display lights up.
- The wash programme stops to “Rinse hold” when the
“Rinse hold” symbol on thedis
“Start
(Pause)”
button blinks as well.
- To terminate the “Rinse hold” by draining the water,
without any spinning, press the
“Start (Pause)”
button.
- To terminate the “Rinse hold” by spinning
the “Variable spin” button to select the desired spin speed
and then
“Start (Pause)”
to start the spin cycle.
- D
If there is a programme setting which you use frequently, the
appliance offers the possibility to save one setting for each
programme so that it can be used again by just pushing one butto
• Select the desired programme, temperature, spin speed and
option(s), push and hold the
“Favourites”
button for at least
3 seconds. The lamp next to
“Favourites”
shortly blinks and
then lights up - the programme setting is saved.
CONSUMPTION DATA
Pro
Te m r u r
(°C)
Load
(kg)
Wa
(l)
Energy
(kWh)
Approx. Programme Duration
(hours : minutes)
*
White Cotton / Antibacter 95 7.0 74
**
2.10 2:10
Cotton 60 7.0 54 1 2:20
Cotton with “Eco”
***
60 7.0 54 0 4:00
Cotton 40 7.0 69 0 2:05
Synthetics 60 3.5 46
**
0.85 1:35
Synthetics 40 3.5 42 0 1:20
Delicates 30 2.5 60 0.40 0:45
W 40 2.0 60 0 0:45
Handwash 40 2.0 45 0 0:40
Jeans 40 7.0 86 0.75 2:21
Big Items 40 3.0 74 0.75 1:30
Sport 30 3.5 54 0.55 1:34
SuperEco 60 7.0 69 0 4:00
Daily load 40 6.0 7 0.60 1:00
Speed 15 30 3.0 30 0 0:15
Consumption values were measured in normalized conditions in compliance with Stane
may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type o
*
The time indicated on the display can deviate froons
applicable at that time.
**
Tut.
***
Reference P
ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME
SELECT ANY DESIRED OPTIO
SA
Next time you want to use your individual programme setting,
select the programme, push the
“Favourites”
button and start by
pushing
“Start (P
.
If you want to replace the saved programme setting by another
one, proceed as already described above.
The “Start delay” allows to run the machine at the consumer’s
convenience, for example at night when electricity is cheaper.
• Select programme, temperature, spin speed and options.
• Press the Start delay button to select one of the delay time
steps between 0:30 and 23:00 hours.
•P
“Start (P
button.
The countdown of the delay time begi
the delay time and the colon between hours and minutes
• The time delay indication disappears when the programme
starts and it is replaced by the remaining programme time.
T
...before you press the “Start (Pause)” button:
• Press the
“Reset / Drain”
button, or set the start delay time to
“0:00” - the delay t
...after having
Press the
“Start (Pause)”
button - the delay time disappears from
the display: press
“Start (Pause)”
again to start the selected
programme immediately
Before starting a programme, the symbol lights to show that the
door can be opened to add more washing. As soon as you press
“Start (Pause)”
, the door will lock until the end of the
programme and must on no account be forced open. In case you
have to open it urgently during a running programme, refer to
“Reset a running programme before the end”.
If you try to start a wash programme and the door is not properly
closed, the “Add garment” indication will blink.
Open the tap and press the
“Start (P
button; the blinking
“Start (Pause)”
button light becomes constant. The “Add
garment” indication goes out, and the lit bubbles indicate that the
programme is in process. In some phases, the remaining
programme time is newly c - if this is the case, the “6
th
sense” indication on the display will fade,
programme time is replaced by an animation.
Activating the child lock prevents children from starting a wash
cycle or changing the settings of a running programme. The child
lock cannot be activated or deactivated when the programme
selector is in thon. To activate the
• Turn the programme selector to a programme position, or run
a programme as usual.
• Press the “Temperad the “Variable spin” button
simultaneously for at least 3 seconds. T
will shortly blink and then light up to indicate that the
child lock is active.
The programme setting cannot be changed anymore; the only change
possible is to switch the washer off b
to the “Off/O” position. To deactivate the child lock, proceed in the
same way as for activating it.
If one of the red failure indications on the display lights up, refer to
the “Troubleshooting Guide” in your “Instructions for Use”.
• The display shows “End”, and the “Programme finished”
indication
1. Turn the programme selector to the “Off/O” position.
2. Clos
3. Open the door and unload the machine.
• Leave the door ajar to allow the drum to dry.
• If you do not turn the programme selector
position, all lights of the control panel go out after a few
minutes to save energy - only “End” will remain
The symbol will light up at the end of the programme if you used
too much detergent. Use less detergent next time. If the symbol
lights up and the display shows “Fod”, too much foam interrupted
the wash process; refer to the “Trouble
Instructions for Use.
1. Press the
“Start (P
button to pause the programme.
The light blinks.
2. Select the new programme, temperature, any options and
another spin speed if you want.
3. Press the
“Start (Pause)”
button again. The new
programme continues at the same position where the
previous programme was interrupted. Do not add detergent
for this programme.
Th
“Reset
button cancels a programme before the end.
•P
“Reset/D
button for at least 3 seconds; an
animation appears on the display
drained out before the door can be opened.
START DELAY
“
PRO
CHILD LOCK
RED FAIL
PROGRAMME END
DETERGENT OVERDOSA
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
RESET A RUNNING PROGRAMME BEFORE
THE END
The Sensor Technology automatically adapts Programme Time, Water and Energy consumption to the size of
30106324GB.fm Page 2 Friday, October 2, 2009 5:15 PM
Black process 45.0° 150.0 LPI
