650530
11
Zoom out
Zoom in
Previous page
1/16
Next page
EN 9
Problem Causes - Solutions - Tips
Detergent residues
on laundry after wash
Whitish residues on dark fabrics are caused by insoluble compounds used in
phosphate-free powder detergents:
- avoid overdosing of detergent; use liquid detergent; select “Intensive Rinse” op-
tion if possible; brush out the fabric.
Programme duration
is considerably
longer or shorter
as indicated in the
“programme chart”
or on the display (if
available)
Normal function of the washing machine to adapt to factors that can have an
effect on the programme duration, like excessive foam formation, load unbalance
due to heavy laundry items, prolonged heating time resulting from low inlet water
temperature etc. Moreover, the sensing system of the washing machine adapts the
programme duration to the size of the wash load.
Depending on these factors, the duration is recalculated during the
programme and updated if necessary; during such periods, an animation
appears on the display (if available). For small loads, the programme time
indicated in the “programme chart” may be reduced by up to 50%.
Description of failure indicators
Failure
indicator blinks
Indication on display
(if available)
Description - Causes - Solutions
Service
from “F03 to “F43
(except F18” and F24”)
“Electrical module fault”
Push the “Reset” button for at least 3 seconds.
F24
May appear for very water-soaking laundry, or if you
added too much laundry for a programme destined for
small loads only. Do not overload the washing ma-
chine. Push the “Reset” button for at least 3 seconds
to stop the programme. Select and start “Rinse and
Spin” programme to complete the interrupted wash
programme properly.
F02 or “FA
“Waterstop fault”
Turn the programme selector to the “Off/O” position,
pull out the mains plug and turn the water tap off.
Then:
Plug in the appliance again.
Turn the water tap on (if water immediately flows
into the appliance without the appliance being
started, there is a failure; turn off the tap and notify
the After-Sales Service).
Select and start the desired programme again.
F18 or “Fod
“Overfoaming”
Too much foam interrupted the wash programme.
If your washing machine has a “Dosing Aid” function,
and you used it: check if the dosing values set for the
different programme groups correspond to the dosing
values recommended for the detergents you use (see
details in separate Instructions for the “Dosing Aid”).
Select and start the “Rinse & Spin” programme.
Afterwards select and start the desired programme
again, using less detergent. See also paragraph
“The machine is at a standstill.... on first page of
Troubleshooting Guide.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Whirlpool DLCE 71469 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Whirlpool DLCE 71469 in the language / languages: English as an attachment in your email.

The manual is 2,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Whirlpool DLCE 71469

Whirlpool DLCE 71469 Quick start guide - English - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info