69380

Whirlpool Denver 1400 Manual

2
Zoom out
Zoom in
Previous page
1/2
Next page
5019 301 06142
Whirlpool is a registered trademark of Whirlpool USA
Add detergent as indicated on the front page and as
described in the chapter “Detergent and Additives”
in your Instructions for Use.
1. Turn the
programme selector
to the desired
programme and temperature.
2. The
time display
shows the duration of the
chosen programme (in hours and minutes), and
the “Start/Pause” indication lamp is flashing.
3. The
indication lamp
of the predefined spin
speed lights up.
Push the button(s) of any option(s) desired - the
respective indication lights up.
When the combination of programme and additional
option(s) is not possible, the indication lights switch off
automatically. Unsuitable combinations of options are
deselected automatically.
“Eco” button
• With a modified temperature profile and a slightly
prolonged washing duration, the optimum
combination of excellent washing result and even
lower energy consumption can be achieved.
“Prewash” button
• Only for heavily soiled loads (for example sand,
granular dirt) sensible. Increases the cycle time
by approximately 15 min.
“Easy ironing” button
• Can be used together with “Cotton”,
“Synthetics” and “Daily load” programmes to
make ironing easier.
• Increases the water quantity and the clothes are
spun very gently.
“Intensive rinse” button
• More water is added and rinse cycle is prolonged.
• This option is particularly suitable for areas with
very soft water, washing baby linen and helps
people with allergies.
“Rinse hold” button
• The laundry remains in the last rinse water
without progressing to the final spin cycle to avoid
creasing and prevent colours from changing.
• This option is particularly recommended for the
programmes “Synthetics”, “Daily load” and “Delicates”.
• It is particularly useful if you want to postpone
spinning to a later time, or if you want to drain only.
Note:
The programme stops to “Rinse hold” at
the time the “Rinse hold” light in the programme
sequence indication is on. The indication lamp
next to the
“Start/Pause”
button flashes.
Terminate the “Rinse hold” option:
•Press the
“Start/Pause”
button; the
programme will terminate automatically with the
final spin cycle for the present wash programme.
•If you do not wish to spin the clothes, turn the
programme selector knob to the “Drain”
programme and press the
“Start/Pause”
button.
“Variable spin” button
• Every programme has a predefined spin speed.
• Press the button to set another spin speed.
• If spin speed “0” is selected, the final spinning is
cancelled but intermediate spin peaks remain
during rinse. The water is drained out only.
CONSUMPTION DATA
Programme
Temperature
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approx. Programme Duration
(hours : minutes)
*
Cotton / Antibacterial 95 7.0 74
**
2.10 2:10
Cotton with “Eco”
***
60 7.0 69 1.33 2:20
Cotton 40 7.0 69 0.75 2:05
Synthetics 60 3.0 46
**
0.80 1:35
Synthetics 40 3.0 42 0.40 1:20
Delicates 30 1.5 60 0.50 0:45
Daily load 40 4.0 48 0.50 1:00
Quick wash 30 4.0 48 0.25 0:30
Wool 40 1.0 60 0.55 0:45
Handwash 40 1.0 45 0.55 0:40
Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home
may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.
*
The remaining time indicator can deviate from the values in the table, because it takes into account the household
conditions
applicable at that time.
**
To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
***
Reference Programme for Energy Label.
ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME
SELECT ANY DESIRED OPTION
The “Start Delay” allows to run the machine at the
consumer’s convenience, for example at night when
electricity is cheaper.
• Select programme, temperature and options.
• Press the “Start Delay” button to select the
delay time by 1 to 23 hours;
•Press the
“Start/Pause”
button.
The indication light next to the “Start Delay”
button lights up and the countdown of the delay
time begins.
•The time delay indication disappears when the
programme starts and it is replaced by the
remaining programme time.
• Once having pressed the
“Start/Pause”
button,
the number of hours preselected can be reduced
by pressing again the “Start Delay” button.
To cancel the “Start Delay”
..before you press the “Start/Pause” button:
• Turn the programme selector to another
position or press the
“Reset”
button.
..after having pressed the “Start/Pause” button:
• Press the
“Reset”
button for at least 3 seconds - the
start delay time disappears from the time display.
Open the tap and press the
“Start/Pause”
button.
The indication lamp next to the
“Start/Pause”
button lights up. The programme sequence indicator
shows the current programme phase, running from
left to right through Wash, Rinse, Spin/Drain.
The time display shows the remaining programme
time. Due to variations in load and temperature of
inlet water, the remaining time is newly calculated in
certain programme phases. If this is the case, an
animation appears on the time display.
Before starting and after end of a programme, the
lamp lights to show that the door can be opened. As
long as a wash programme is running, the door
remains locked and must on no account be forced
open. In case you have an urgent need to open it
during a running programme, refer to “Cancel
(Reset) a running programme before the end”.
“Service”
Lighting up of the “Service” indication can be caused by
a fault in an electrical component. Refer to the
“Troubleshooting Guide” in your Instructions for Use; if
the fault persists, contact our After Sales Service.
“Water tap closed”
The appliance has no or insufficient water supply.
Open the water tap; if the indication still lights up,
refer to the “Troubleshooting Guide” in the
Instructions for Use.
“Clean pump”
Waste water is not pumped out. Check whether the
drain hose is kinked or the filter must be cleaned; in
the latter case refer to the Instructions for Use
(“Removing the Filter”).
• All the lights of the programme sequence indicator
are off, and the “Door open” indication lights up.
1. Turn the programme selector to the “Off/O”
position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
1. Press the
“Start/Pause”
button to pause the
programme. The light flashes.
2. Select the new programme (with temperature),
any options and another spin speed if you want.
3. Press the
“Start/Pause”
button again. The new
programme continues at the same position where
the previous programme was interrupted. Do not
add detergent for this programme.
The
“Reset”
button cancels a programme before
the end.
•Press the
“Reset”
button for at least 3
seconds. Any existing water is drained out
before the door can be opened.
START DELAY
PROGRAMME START
“DOOR OPEN” INDICATION
RED INDICATIONS
PROGRAMME END
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
CANCEL (RESET) A RUNNING
PROGRAMME BEFORE THE END
30106142GB.fm Page 2 Wednesday, January 16, 2008 5:49 PM
Black process 45.0° 100.0 LPI
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Whirlpool Denver 1400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Whirlpool Denver 1400 in the language / languages: English as an attachment in your email.

The manual is 0,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Whirlpool Denver 1400

Whirlpool Denver 1400 User Manual - English - 14 pages

Whirlpool Denver 1400 Quick start guide - German - 2 pages

Whirlpool Denver 1400 User Manual - German - 15 pages

Whirlpool Denver 1400 Quick start guide - Dutch - 2 pages

Whirlpool Denver 1400 User Manual - Dutch - 13 pages

Whirlpool Denver 1400 Quick start guide - French - 2 pages

Whirlpool Denver 1400 User Manual - French - 13 pages

Whirlpool Denver 1400 User Manual - Italian - 13 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info