650585

Whirlpool AWOA7123 Manual

2
Zoom out
Zoom in
Previous page
1/2
Next page
ADD DETERGENTS, CLOSE THE DOOR AND
SELECT THE PROGRAMME
Load the laundry, close the door and add
detergents as indicated on the front page and
as described in the chapter “Detergent and
Additives” in your Instructions for Use.
Turn the programme selector to the desired
programme and temperature. The indication
lamp next to “Start/Pause” button blinks.
Your washing machine is designed to save
energy. After the end of a programme, or when a
programme is selected but not yet started, the
washing machine will therefore switch off
automatically after about a quarter of an hour.
To switch the washing machine on again,
turn the programme selector to “O” and
afterwards to the desired programme again.
CONSUMPTION DATA
Programme
Temperature
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approx. programme
duration
(hours : minutes)
%
Cotton with prewash 95 7.0 84 **** 2.40 2:49
59
Cotton 60 7.0 54 1.19 2:20
Cotton 40 7.0 66 1.00 2:45
Synthetics with prewash 60 3.0 63** 1.20 2:34
40
Synthetics 60 3.0 50** 1.00 2:15
Synthetics 40 3.0 46 0.70 2:15
Delicates 30 1.5 60 0.40 0:46
Quick Wash 30´ 30 3.0 48 0.25 0:30
Wool/Hand 40 1.0 45 0.55 0:40
Wool/Hand cold 1.0 45 0.10 0:35
Cotton
60°
* 60 7.0 50 0.91 4:00
53
Cotton
60°
* 60 3.5 40 0.85 3:00 ***
Cotton
40°
* 40 3.5 40 0.65 3:00 ***
Power consumption in off-mode 0.16 W / in left-on mode 0.16 W
SELECT ANY DESIRED OPTION
Push the button of any option desired - the
respective indication lamp lights up.
If the combination of programme and additional
option(s) is not possible, the indication lights
switch off automatically.
“Spin speed reduction” button
• Reduces the predetermined automatic
maximum spin speed to treat your laundry
more gently.
“Rinse hold” button
• The laundry remains in the last rinse water
without progressing to the final spin cycle
to avoid creasing and prevent colours from
changing.
• Particularly useful if you want to postpone
spinning to a later time, or if you want to drain
only.
• The programme stops to “Rinse hold” at
the time the “Rinse hold” indicator in the
programme flow bar is on. The indication lamp
next to the “Start/Pause” button blinks.
Terminate the “Rinse hold” option :
• Press the “Start/Pause” button ; the
programme will terminate automatically with
the final spin cycle for the present wash
programme.
• If you do not wish to spin the clothes, turn the
programme selector to the “Drain” programme
and press the “Start/Pause” button.
PROGRAMME START
Open the tap and press the “Start/Pause”
button. The indication lamp next to the “Start/
Pause” button lights up. The programme flow
bar shows the current programme phase,
running from left to right through Wash, Rinse,
Spin/Drain.
“DOOR OPEN” INDICATION
Before starting and after end of a programme,
the lamp lights to show the the door can be
opened. As long as a wash programme is
running, the door remains locked and must on
no account be forced open. In case you have
an urgent need to open it during a running
programme, refer to “Cancel (Reset) a running
programme before the end”.
FAILURE INDICATIONS
In case of any failures or irregularities, consult
the “Troubleshooting Guide” in your Instructions
for Use.
“Water tap closed”: no or not sufficient inlet
water.
”Service”: failure or malfunction of an electrical
component.
”Clean pump”: waste water is not pumped out.
PROGRAMME END
The “Door open” indicator lights up. After about
a quarter of an hour, the washing machine will
switch off completely to save energy.
1. Turn the programme selector to the “O”
position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
1.
CHANGE PROGRAMME AND/OR OPTIONS AF-
TER PROGRAMME START
Press the “Start/Pause” button to pause the
programme. The light blinks.
2. Select the new programme (with
temperature), and any options if you want.
3. Press the “Start/Pause” button again. The
new programme continues at the same
position where the previous programme was
interrupted. Do not add detergent for this
programme.
CANCEL (RESET) A RUNNING PROGRAMME
BEFORE THE END
The “Reset” button cancels a programme
before the end.
• Press and hold the “Reset” button for a few
seconds. Any existing water is drained out.
It may last some time until the door can be
opened.
Consumption values were measured in normalized conditions, in compliance with IEC/EN 60456. In the home, they may vary depending on the individual water
supply pressure and temperature, the load and the type of wash. The consumption data indicated are based on an inlet water temperature of approx. 15°C through
the cold fill valve as well as the hot fill valve (if available). If your washing machine has a hot fill valve, connection of this valve to hot water supply will lower the
energy consumption by reduced heating times, depending on the individual hot fill inlet water temperature. Water and energy consumptions refer to the default
setting of the programmes, with temperature and load as indicated in the table; selecting any options or changing the spin speed will also change the consumption
data.
The programme duration may differ from the values indicated above as it depends on the operation conditions applicable at that time (see also
“Troubleshooting Guide” in your Instructions for Use).
Approximate remaining moisture content (%). After programme end, in default programme setting.
* Reference programmes for Energy Label. For reasons of energy saving, the real water temperature may deviate from the declared cycle temperature.
** To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
*** Automatic adaptation of programme duration after detection of wash load
**** Cool down water and prewash water
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Whirlpool AWOA7123 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Whirlpool AWOA7123 in the language / languages: English as an attachment in your email.

The manual is 0,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Whirlpool AWOA7123

Whirlpool AWOA7123 User Manual - English - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info