650585
10
Zoom out
Zoom in
Previous page
1/16
Next page
EN 8
TROUBLESHOOTING GUIDE
Your washing machine is equipped with automatic safety functions which detect and diagnose faults at
an early stage and allow you to react appropriately. These faults are frequently so minor that they can be
removed within a few minutes.
Problem Causes - Solutions - Tips
Appliance does not start,
no indicators are on
Plug is not properly inserted in socket.
Socket or fuse does not function correctly (use a table lamp or similar
appliance to test it).
The washing machine is switched off automatically to save energy,
before programme start or after programme end. To switch on the
washing machine, turn the programme selector first to “Off/O” and then
to the desired programme again.
Appliance does not start
although “Start(Pause)”
has been pressed
Door is not properly closed.
The “Child lock/Lock buttons” feature has been activated (if
available on your model). To unlock the buttons, push the two buttons
marked with the key symbol simultaneously and hold them at least for 3
seconds. The key symbol on the display disappears and the programme
can be started.
Appliance stops during the
programme, and the
“Start(Pause)” indicator
blinks
“Rinse hold” is activated. Press “Start(Pause) to spin the laundry.
For draining the water without spinning, select “Drain” programme (if
available) or press the “Reset/Drain” button for at least 3 seconds.
Programme has been changed - reselect desired programme and press
Start/Pause”.
Programme has been interrupted and eventually door has been opened
- close door and restart programme by pressing “Start(Pause)”.
The appliance’s safety system has been activated (see “Failure
indicators” in your programme chart).
Water tap is not opened or water inlet hose is kinked or blocked (“Water
tap closed” indicator blinks).
Detergent dispenser
contains residues from
detergent and/or additives
Water entering is not enough; the mesh filters of the water supply could
be blocked (see “Care And Maintenance”).
Appliance vibrates during
spin cycle
Transport bolts have not been removed; before using the machine, it
is imperative that the transport bolts are removed.
Appliance is not level / not standing firmly on all four feet (see separate
“Installation Guide”).
Final spin results are poor
Unbalance during spinning prevented spin phase to protect the washing
machine (see “Unbalance during spinning”).
Excessive foam formation prevented spinning; select and start “Rinse &
Spin” programme. Avoid excessive detergent dosing (see “Detergents
And Additives”).
“Spin” button has been set to a low spin speed.
Unbalance during spinning”
The “Spin/Drain” indicator
in the programme flow bar
blinks, or the spin speed on
the display blinks, or the spin
speed indicator blinks after
the end of the programme
(depending on the model).
The laundry is still very wet.
Unbalance of the laundry load during spinning prevented the spin phase
to avoid damages on the washing machine. This is why the laundry is still
very wet.
Reason for unbalance can be: small laundry loads (consisting of only few
quite big or absorbent items, e.g. towels), or big/heavy laundry items.
If possible avoid small laundry loads.
It is highly recommended that you add other laundry items of different-
sizes when washing a big or heavy piece of laundry.
If you want to spin the wet laundry, add more laundry items of different
sizes, and subsequently select and start the “Rinse & Spin” programme.
The washing machine is at a
standstill for several minutes
in the middle of a running
programme; the wash
programme seems not to
proceed
Normal function of the washing machine used for optimizing the rinse
phase. One reason for such a pause can be that you might have used too
much detergent; the washing machine automatically interrupts the pro-
gramme to have the foam reduced. This standstill may be repeated several
times until the foam reduction is sufficient to continue the wash cycle. If the
foam persists, the red “Service” indicator will light up and the display shows
“F18” or “Fod” - refer to the instructions concerning the “Service” indication
on the next pages in this case.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Whirlpool AWOA7123 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Whirlpool AWOA7123 in the language / languages: English as an attachment in your email.

The manual is 2,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Whirlpool AWOA7123

Whirlpool AWOA7123 Quick start guide - English - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info