Not all soil levels are selectable for each programme.
“Spin” button (incl. “Rinse hold” )
• Every programme has a predefined spin speed.
• Press the button to set another spin speed.
• If you select spin speed “0”, the final spinning is cancelled and
the water is drained out only. However, intermediate spin
phases remain during the rinse.
• If you select “Rinse hold”, the laundry remains in the last rinse
water without progressing to the final spin cycle, to avoid
creasing and prevent colours from changing. To activate the
“Rinse hold”, press the “Spin” button repeatedly until the
“Rinse hold” symbol on the display lights up.
- The wash programme stops to “Rinse hold” when the
“Rinse hold” light in the programme sequence indicator is
on; the light of “Start/Pause” button blinks.
“DOOR OPEN” INDICATION
Before starting and after end of a programme, the lamp lights to
show the the door can be opened. As long as a wash programme
is running, the door remains locked and must on no account
be forced open. In case you have an urgent need to open it
during a running programme, refer to “Cancel (Reset) a running
programme before the end”.
PROGRAMME START
Open the tap and press the “Start/Pause” button .
The indication lamp next to the “Start/Pause” button lights up.
The programme sequence indicator shows the current
programme phase, running from left to right through Wash,
Rinse, Drain/Spin.
PROGRAMME END
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
1. Press the “Start/Pause” button to pause the programme.
The light blinks.
2. Select the new programme, temperature, any options and
another spin speed if you want.
3. Press the “Start/Pause” button again. The new programme
continues at the same position where the previous
programme was interrupted. Do not add detergent for this
programme.
CANCEL (RESET) A RUNNING PROGRAMME
BEFORE THE END
The “Reset/Drain” button cancels a programme before the end.
• Press and hold the “Reset/Drain” button for a few seconds;
an animation appears on the display. The water is drained out;
it may last some time until you can open the door.
The “Start delay” allows to run the machine at the consumer’s
convenience, for example at night when electricity is cheaper.
Do not use liquid detergent when activating “Start delay” option.
• Select programme, temperature, spin speed and options.
• Press the Start delay button to select a delay time up to
23 hours.
• Press the “Start/Pause” button. The countdown of the delay
time begins; the start delay symbol and the colon between
hours and minutes blink.
• The time delay indication disappears when the programme
starts and it is replaced by the remaining programme time.
• If you use the “Dosing Aid” button: select the delay time
BEFORE pressing the “Dosing Aid” button.
The countdown of the selected delay time begins after
having pressed the “Start/Pause” button for the second
time (see separate Instructions for Use concerning the
“Dosing Aid”).
To cancel the “Start delay”
...before you press the “Start/Pause” button:
• Press the “Reset/Drain” button , or set the start delay time
to “0:00” - the delay time disappears after a few seconds.
...after having started the programme:
• Press the “Start/Pause” button - the delay time disappears
from the display. Press “Start/Pause” again if you want to
start the selected programme immediately.
SET A START DELAY
FAILURE INDICATIONS
DETERGENT OVERDOSAGE INDICATION
The symbol will light up at the end of the programme if you used
too much detergent. Use less detergent next time.
If the symbol lights up and the display shows “Fod”, too much
foam interrupted the wash process; refer to the
“Troubleshooting Guide” in your Instructions for Use.
With the “Dosing Aid” button, you can make your washing
machine indicate you the recommended detergent quantity for
your wash load, depending on the soil level selected and the size
of the load.
• Helps to save detergent and protect the environment and
also sensitive skin by avoiding detergent overdosing.
• Before you use this function, you must adapt the washing
machine to the dosing amounts which are recommended
for the detergents you use. Also check if your region’s
water hardness corresponds with the water hardness level
“soft” of your washing machine - if not adapt it.
• Select programme, options and start delay BEFORE using
the “Dosing Aid” button. For any details, refer to the
separate “Dosing Aid” Instructions for Use.
DETERGENT DOSING RECOMMENDATION
CHILD LOCK
Activating the child lock prevents children from starting a wash
cycle or changing the settings of a running programme.
The child lock cannot be activated or deactivated when the
programme selector is in the “Off/O” position. To activate
the child lock:
• Turn the programme selector to a programme position, or
run a programme as usual.
• Press the 2 buttons marked with the key symbol
simultaneously for at least 3 seconds. A key-like symbol will
shortly appear on the display to indicate that the child lock is
active.
Any time you try to change a programme setting with active
child lock, the display will briefly show the key-like symbol.
The programme setting cannot be changed anymore. The only
change possible is to switch the washer off by turning the
programme selector to the “Off/O” position.
To deactivate the child lock:
• Press again the 2 buttons marked with the key symbol
simultaneously for at least 3 seconds.
- To terminate the „Rinse hold“ by spinning the laundry, press
“Start/Pause” - the laundry will be spun with the default
spin speed. You can also select another spin speed with the
„Spin“ button before you start the spin cycle by pressing
“Start/Pause”.
- To terminate the „Rinse hold“ by draining the water without
spinning, press the „Spin“ button until spin speed „0“ appears
on the display; then press “Start/Pause” to start the
draining.
- Do not leave the laundry to soak for too long in the
“Rinse hold”.
Whirlpool is a registered trademark of Whirlpool USA.
5019 300 00480
The “Door open” indicator lights up, and the display shows
“End”. After about a quarter of an hour, the washing machine will
switch off completely to save energy.
1. Turn the programme selector to the “Off/O” position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
In case of any failures or irregularities, consult the
“Troubleshooting Guide” in your Instructions for Use.
“Water tap closed”: no or not sufficient inlet water.
”Service” : failure or malfunction of an electrical component.
”Clean pump”: waste water is not pumped out.
Spin speed on display blinks : unbalance during spinning.
CONSUMPTION DATA
Consumption values were measured in normalized conditions, in compliance with IEC/EN 60456. In the home, they may vary depending on the individual
water supply pressure and temperature, the load and the type of wash. The consumption data indicated are based on an inlet water temperature of approx.
15°C through the cold fill valve as well as the hot fill valve (if available). If your washing machine has a hot fill valve, connection of this valve to hot water supply
will lower the energy consumption by reduced heating times, depending on the individual hot fill inlet water temperature. Water and energy consumptions
refer to the default setting of the programmes, with temperature and load as indicated in the table; selecting any options or changing the spin speed will also
change the consumption data.
The programme duration may differ from the values indicated above as it depends on the operation conditions applicable at that time (see also
“Troubleshooting Guide” in your Instructions for Use).
* Reference programmes for Energy Label. For reasons of energy saving, the real water temperature may deviate from the declared cycle temperature.
** To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
*** Automatic adaptation of programme duration after detection of wash load
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Whirlpool AWO-D 7224 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Whirlpool AWO-D 7224 in the language / languages: English as an attachment in your email.
The manual is 0,88 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
