- the sensor technology adapts water, energy and programme duration to the size of your wash load.
CONSUMPTION DATA
Consumption values were measured in normalized conditions, in compliance with IEC/EN 60456. In the home, they may vary depending on the individual water supply
pressure and temperature, the load and the type of wash. The consumption data indicated are based on an inlet water temperature of approx. 15°C through the cold fill
valve as well as the hot fill valve (if available). If your washing machine has a hot fill valve, connection of this valve to hot water supply will lower the energy consumption by
reduced heating times, depending on the individual hot fill inlet water temperature. Water and energy consumptions refer to the default setting of the programmes, with
temperature and load as indicated in the table; selecting any options or changing the spin speed will also change the consumption data.
The programme duration may differ from the values indicated above as it depends on the operation conditions applicable at that time (see also “Troubleshooting
Guide” in your Instructions for Use).
* Reference programmes for Energy Label. For reasons of energy saving, the real water temperature may deviate from the declared cycle temperature.
** To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
*** Automatic adaptation of programme duration after detection of wash load
Power consumption in off-mode 0.16 W / in left-on mode 0.16 W
Whirlpool is a registered trademark of Whirlpool USA.
5019 300 00436
SELECT ANY DESIRED OPTION
When the combination of programme and additional
option(s) is not possible, the indication switch off
automatically.
“Prewash” button
•Adds a prewash cycle to the wash programme selected;
prolongs the programme by about a quarter of an hour.
• Recommended for heavily soiled laundry (e.g. with sand
or granular dirt).
•Do not use liquid detergent for the main wash when
activating the “Prewash” option.
“Rapid” button
• Enables quicker washing by shortening the programme
duration.
• Recommendable for only lightly soiled laundry.
• Not selectable for Cotton 95°C.
“Clean+” button
•Choose this option if you use an in-wash additive for
stain removal (powder, for example “Vanish”) - it will
optimize the additive’s efficiency to get better wash
performance and stain removal.
• Use with maximum load.
• Add an appropriate amount of in-wash additive for stain
removal (powder) to the main wash chamber, together
with your detergent (only use powder detergent with this
option). Respect the manufacturer’s dosing instructions.
• May prolong the programme by up to 15 minutes
• Appropriate for use of stain removers and bleaches
on oxygen basis. Chlorine or perborate bleaches
must not be used!
“Colours 15°” button
• Saves energy used for water heating while maintaining a
good wash result.
• Supports colour maintenance when washing coloured
laundry.
• Recommendable for lightly soiled laundry without stains.
• Make sure that your detergent is suitable for cold wash
temperatures (15 or 20°C).
• Not selectable for Cotton 95°C.
“Intensive rinse” button
•More water is added and rinse cycle is prolonged.
•This option is particularly suitable for areas with very soft
water, washing baby linen and helps people with allergies.
“Easy ironing” button
•Reduces creasing by an increased water quantity and
a very gentle spin.
“Rinse hold” button
•The laundry remains in the last rinse water without
pregressing to the final spin cycle to avoid creasing and
prevent colours from changing.
Before starting and after end of a programme, the lamp
lights to show the the door can be opened. As long as a wash
programme is running, the door remains locked and must on
no account be forced open. In case you have an urgent need
to open it during a running programme, refer to “Reset” a
running programme before the end”.
Open the tap and press the “Start/Pause” button .
The indicator next to the “Start/Pause” button lights up.
When the laundry load is detected or the programme
duration is updated, the display shows an animation.
FAILURE INDICATION
The “Door open” indicator lights up, and the display shows
“End”. After about a quarter of an hour, the washing
machine will switch off completely to save energy.
1. Turn the programme selector to the “Off/O” position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
1. Press the “Start/Pause” button to pause the programme.
The light blinks.
2. Select the new programme, temperature, any options
and another spin speed if you want.
3. Press the “Start/Pause” button again.
The new programme continues at the same position
where the previous programme was interrupted.
Do not add detergent for this programme.
CANCEL (RESET) A RUNNING PROGRAMME
BEFORE THE END
The “Reset” button cancels a programme before the end.
• Press and hold the “Reset” button for a few seconds;
an animation appears on the display. The water is drained
out; it may last some time until you can open the door.
With this function you can postpone your programme to
complete at a later time: press the button to select in how
many hours the programme shall be finished. Thus, it allows
you to have your laundry ready at a particular time and to
profit from more favorable energy rates during the night, for
example. Do not use liquid detergent when activating “Cycle
end” option.
• The time until the “Cycle end” can be selected in full
hour time segments (1 to 24 h). When you press the
button, the shortest possible time will be displayed; keep
on pressing the button to loop through all the available
times. To remove it again, keep on pressing the button
until you see the value “0:00”.
• When you have selected the desired time until the “Cycle
end”, press “Start/Pause” - the countdown will begin.
• During the countdown, you can still modify the
programme setting (select or deselect options, change
spin speed etc.). If the modifications prolong the
programme duration so that it overruns the originally set
time until the “Cycle end”, the programme will start
immediately.
• Sometimes the programme may finish before the
selected time until the “Cycle end” has expired (e.g. for
small loads). In this case, the washing machine will tumble
the laundry regularly to keep it fresh, until the selected
“Cycle end” time has expired. During tumbling, the
display will show an animation. The tumbling phase can
be stopped at any time either by pressing any button or
by rotating the programme selector; the animation will
stop and the door will unlock in about 1 minute as
indicated on the display.
In case of any failures or irregularities, consult the
“Troubleshooting Guide” in your Instructions for Use.
“Water tap closed”: no or not sufficient inlet water
”Service”: failure or malfunction of an electrical
component
”Clean pump”: waste water is not pumped out.
Spin speed on display blinks: unbalance during spinning.
The „Eco monitor“ gives you a rough feedback about the
power consumption of the programme setting you selected.
As soon as you turn the programme selector to any progra-
mme, the „Eco monitor“ is on.
less more
PROGRAMME END
ECO MONITOR
SET CYCLE END
PROGRAMME START
“DOOR OPEN” INDICATION
•It is particularly useful if you want to postpone spinning to
a later time, or if you want to drain only.
•The wash programme stops to “Rinse hold” when the
“Rinse hold” indicator on the display blinks. The “Start/
Pause” indicator blinks as well.
Terminate the “Rinse hold” option:
•Press the “Start/Pause” button; the programme will
terminate automatically with the final spin cycle for the
present wash programme.
•If you do not wish to spin the clothes, turn the
programme selector to the “Drain” programme and press
the “Start/Pause” button.
“Spin” button
•Every programme has a predefined spin speed.
•Press the button to set different spin speed.
•If spin speed “0” is selected, the final spinning is cancelled
but intermediate spin peaks remain during rinse.
The water is drained out only.
M
LOAD LAUNDRY, ADD DETERGENTS
AND SELECT THE PROGRAMME
Load the laundry, add detergent and turn the programme
selector tothe desired programme and temperature; the
“Start/Pause” indicator blinks. The spin speed shown on
the display can be altered by pressing the “Spin” button
If you do not start the programme soon after having
made your choice, the washing machine will switch off
automatically after about a quarter of an hour. To switch the
washing machine on again, turn the programme selector to
“Off/O” and afterwards to the desired programme again.
The indicator on the left is to show that the „Eco monitor“ is
active. The four indicators next to it show the degree of
consumption: the less power your programme setting is
forecasted to consume, the less indicators will light up. This
depends on the programme, temperature and options selec-
ted, and also on the size of the wash load. For that reason,
the forecasted degree of power consumption may adapt
On the left i can select the washing programs and on the right i can select temperature, but i dont know if i can select both. I mean i can put the selector either on a specific program, like for white laundry, or on a temperature. is there a way to select both?
Submitted on 13-10-2021 at 11:28
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Whirlpool AWO-C 6340 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Whirlpool AWO-C 6340 in the language / languages: English as an attachment in your email.
The manual is 1,27 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
