578852
9
Zoom out
Zoom in
Previous page
1/13
Next page
97
TROUBLESHOOTING GUIDE
Depending on the model, your washing machine is
equipped with various automatic safety functions.
This enables faults to be detected in good time and
the safety system can react appropriately. These
faults are frequently so minor that they can be
removed within a few minutes.
The washing machine will not start, no
indicator lamps are on.
Check whether:
the mains plug is inserted into the socket
the wall socket is functioning correctly (use a
table lamp or similar appliance to test it)
The washing machine will not start... and the
“Start/Pause” indicator lamp flashes.
Check whether:
the door is properly closed (child safety);
the “Start/Pause” button has been pressed.
In models with LCD display, the display shows:
the water tap is closed. For models with a
“Water tap closed” indicator lamp, the red
indicator lamp lights up. Open the tap and press
the “Start/Pause” button.
The appliance stops during the programme
(varies depending on model)
Check whether:
the “Rinse Hold” indicator lamp is flashing;
terminate this option by pressing the button
again
In models with LCD display: the “Rinse Hold”
option has been preselected and the “Rinse
Hold” symbol appears on the display; cancel this
option by pressing the “ ” button or select
the “Drain” programme
another programme has been selected and the
“Start/Pause” indicator lamp is flashing. Reselect
the desired programme and press the
“Start/Pause” button
the door has been opened and the “Start/Pause”
indicator lamp is flashing. Close the door and
press the “Start/Pause” button again. In models
with LCD display, the display shows: “PAUSE!”
the washing machine's safety system has been
activated (see “Fault display chart”)
Residue from detergent and additives left in
the detergent drawer at end of wash.
Check whether:
the siphon is correctly installed and clean (see
“Care And Maintenance”)
sufficient water is entering.
The mesh filters of the water supply could be
blocked (see “Care And Maintenance”)
When using powder detergent beforehand the
coloured insert for dosing liquid detergent has
been removed from the dispenser
Machine vibrates during spin cycle.
Check whether:
the washing machine is level and standing firmly
on all four feet
the transit bolts have been removed. Before
using the machine, it is imperative that the
transport bolts are removed
Final spin results are poor.
The washing machine has an imbalance detection
and correction system.
If individual heavy items are loaded (e.g. bathrobes),
this system may reduce the spin speed
automatically or even interrupt the spin completely
if it detects too great an imbalance even after
several spin starts, in order to protect the washing
machine.
In models with LCD display, in the event of an
imbalance, the display shows:
If the laundry is still too wet at the end of the
cycle, add smaller articles of laundry and repeat
the spin cycle
Excessive foam formation may prevent spinning.
Use the correct amount of detergent
In models with LCD display, the display shows:
Check that the spin speed selector has not been
set to “0”
30105594aGB.fm Page 97 Thursday, December 30, 2004 10:39 AM
Black process 45.0° 100.0 LPI
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Whirlpool AWO 10360 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Whirlpool AWO 10360 in the language / languages: English as an attachment in your email.

The manual is 0,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Whirlpool AWO 10360

Whirlpool AWO 10360 User Manual - English - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info