307429
2
Zoom out
Zoom in
Previous page
1/16
Next page
BEFORE USING THE WASHING MACHINE
1.Remove the packaging and check
After unpacking, make sure that the washing
machine is undamaged. If in doubt, do not use
the washing machine. Contact After-Sales
Service or your local dealer.
Keep the packaging materials (plastic bags,
polystyrene parts, etc.) out of reach of children,
since it is a possible source of danger.
If the appliance was exposed to the cold prior to
delivery, keep it at room temperature for a few
hours before operating.
2.Remove the transit bolts
The appliance is fitted with transit bolts to
prevent internal damage during transport.
Before using the washing machine you must
remove the transit bolts
(see “Installation”/
”Remove the transit bolts”).
3.Install the washing machine
Install the appliance on a solid and level floor
surface. In the case of a yielding sub-floor, the
appliance should be installed in the corner of a
room.
Adjust the feet to ensure that the machine is
stable and level on the floor (see “Installation”/
”Adjust the feet”).
In case of wooden or so-called “floating floors”
(for instance certain parquet or laminate floors),
place the appliance on a 60 x 68 cm sheet of
plywood at least 3 cm in thickness which is
secured to the floor.
4.Water inlet
Connect the water supply inlet hose in
accordance with the regulations of your local
water company (see “Installation”/”Connect the
water supply hose” and instructions on the hose
bag).
Water supply: Cold water only (if no other
information on programme
chart)
Tap: 3/4” threaded hose connection
Pressure: 100-1000 kPa (1-10 bar).
Use only new hoses to connect the washing
machine to the water supply. Used hoses must
not be used and should be discarded.
5.Drain hose
Connect the drain hose to the ventilated siphon
or hook it over the edge of a sink by means of
the “U” bend (see “Installation”/”Connect the
water drain hose”).
6.Electrical connections
Electrical connections must be carried out by a
qualified electrician in compliance with the
manufacturer's instructions and local safety
regulations.
Voltage information, power consumption and
electrical fusing data are supplied on the front
panel behind the door frame.
The appliance must be connected to the mains
exclusively by means of a socket with an earth
connection in accordance with established
regulations. The appliance must be earthed by
law. The manufacturer declines all liability for
possible damage to property or injury to persons
or pets deriving from failure to observe the a/m
directions.
Do not use extension leads or multi sockets.
Before any maintenance on the washing
machine disconnect the power plug or switch off
the power supply.
Access to the mains plug or to disconnection from
mains supply via a double-pole switch must be
ensured at all times following the installation.
Do not operate the washing machine if it has
been damaged during transport. Inform the
After-Sales Service.
Mains cable replacement is only to be carried out
by After-Sales Service.
The washing machine must only be used in the
household for the prescribed uses.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Whirlpool awm1001 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Whirlpool awm1001 in the language / languages: English as an attachment in your email.

The manual is 0,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info