315204

Whirlpool awm 6103 Manual

2
Zoom out
Zoom in
Previous page
1/2
Next page
5019 301 10216
Whirlpool is a registered trademark of Whirlpool USA.
Prewash cycle might increase programme duration. Consumption values were measured in normalized conditions in
compliance with Standard IEC/EN 60 456. Consumption data in the home may vary with respect to the values in the table
in relation to the water supply pressure and temperature, the load and the type of wash.
* The remaining time indicator can similarly deviate from the values in the table, because it takes into account the
household conditions applicable at that time.
** To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains
the water out.
Add the detergent as described in the programme
table or in the chapter “Detergents and Additives” in
the booklet.
1. Turn the
programme selector knob
to the
desired programme and temperature.
2. The remaining time display shows the duration of
the chosen programme (in hours and minutes)
and after taking some seconds for calculating, the
pilot lamp of the
“Start/Pause”
button is
flashing.
3. The programme sequence and the predefined
spin speed indication corresponding to the
selected programme lights up.
Selecting any option the indication lights up.
When the combination of programme,
additional options and temperature is not
possible, the indication lights switch off
automatically. Unsuitable combinations of
options are deselected automatically.
“Easy Ironing” button
• Can be used together with Cotton, Synthetics
and Daily programmes to make ironing easier.
• Increases the water quantity and the clothes are
spun very soft.
“Prewash” button
• Only for heavily soiled loads (for example sand,
granular dirt) sensible. The cycle time increases
approximately 15 min.
“Intensive Rinse” button
• More water and a longer time in rinse cycle is
added.
• This option is particularly suitable for areas with
very soft water, washing baby linen and helps
people with allergies.
“Rinse Hold” button
• The laundry remains in the last rinse water
without progressing to the final spin cycle to
avoid creasing and prevent colours from
changing.
• This option is particularly recommended for the
programme “Synthetics”, “Daily” and
“Delicates”.
• This function is particularly useful if you want to
postpone spinning to a later time, or if you want
to drain only.
CONSUMPTION DATA
Programme
Temperature
Selector
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approx.
Programme
Duration
(hours : minutes)*
Cotton 95 5.5 54** 1.90 2:00
Cotton 60 5.5 49 1.04 2:25
Cotton 40 5.0 44 0.60 2:05
Synthetics 60 2.5 55 0.80 1:30
Synthetics 40 2.5 55 0.60 1:20
Short 30 3.0 37 0.40 0:30
Delicates 40 1.5 60 0.60 0:45
Wool 30 1.0 60 0.30 0:40
Silk 30 1.0 45 0.30 0:40
ADD DETERGENTS, CLOSE THE DOOR AND
SELECT THE PROGRAMME
SELECT ANY DESIRED OPTION
Note:
The programme stops to “Rinse Hold” at
the time the “Rinse Hold” light in the programme
flow indication is on.
Terminate the “Rinse Hold” option:
• Press the “Rinse Hold” button again; the
programme will terminate automatically with
the final spin cycle for the present wash
programme.
• If you do not wish to spin the clothes, turn the
programme selector knob counterclockwise to
the “Drain” programme and press the
“Start/
Pause”
button again when flashing.
“Spin Speed Reduction” button
• Every programme has an automatic predefined
maximum spin speed.
• Press the button to set another spin speed.
• If the spin speed “
0
” is selected, the final
spinning is cancelled but intermediate spin
peaks remain during rinse. The water is drained
out only.
The “Start Delay” allows to run the machine at the
consumer’s convenience, for example at night
when electricity is cheaper.
• Press the “Start Delay” button to select the
delay time by 1 to 23 hours;
• Press the
“Start/Pause”
button.
• The time delay indication disappears when the
programme starts and it is replaced by the
remaining time.
• The number of hours preselected can later be
reduced pressing again the “Start Delay”
button.
To cancel the “Start Delay”.
• Turn the programme selector to the “ ”
position.
• Reselect the desired programme and options
and press the
“Start/Pause”
button.
Open the tap and press the
“Start/Pause”
button. The pilot lamp of the
“Start/Pause”
button lights up.
The indicator lamps show the sequence reached in
the programme. After starting the programme, the
sequence indication runs from left to right through
Wash, Rinse, Spin.
When the sequence of the programme is finished
the corresponding lamp goes out.
The door can be opened when the “Door Open”
indication is on.
• The remaining time is on “0:00” and all the
lights of the programme sequence indication
are off.
1. Turn the programme selector to the
“”
position.
2. Turn the water supply tap off.
3. Open the door and unload the machine.
4. Close the tap and leave the door ajar to allow
the drum to dry out.
1. Press the
“Start/Pause”
button to pause the
programme. The light flashes.
2. Select the new programme (with
temperature), any options and another spin
speed if you want.
3. Press the
“Start/Pause”
button again. The
new programme continues at the same
position where the previous programme was
interrupted. Do not add detergent for this
programme.
1. Press the
“Start/Pause”
button to pause the
programme. The light flashes.
2. Set the programme selector to “Drain”. The
spin indicators show
“0”
and the remaining
time shows “0:02”.
3. Press the
“Start/Pause”
button to start the
drain programme.
START DELAY
PROGRAMME START
DOOR LOCK
PROGRAMME END
CHANGE THE PROGRAMME, OPTIONS
AFTER PROGRAMME START
CANCEL A PROGRAMME BEFORE THE
END
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Whirlpool awm 6103 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Whirlpool awm 6103 in the language / languages: English as an attachment in your email.

The manual is 0,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info