366791
14
Zoom out
Zoom in
Previous page
1/19
Next page
14
TROUBLESHOOTING GUIDE
The appliance will not start, no lamp lights up.
Check whether:
the appliance is plugged in;
the wall socket is functioning correctly
(use a table lamp or similar).
ON/OFF button pressed.
The appliance will not start, but the “On/Off”
lamp is on.
Check whether:
the appliance door is properly closed
(child safety);
a programme has been selected and the programme
is started;
the water tap is open.If not, open the tap and switch
the appliance first off, then on.
The appliance stops during the programme.
Check whether:
the
“Rinse Hold”
button is pushed, terminate this
option by pressing the button again;
•“On/Off
lamp is off. Press
“On/Off”
button;
No water or insufficient water supply.
Check whether:
the tap is turned on completetly;
kinks are present in water hose;
the water hose filter is blocked;
the water hose is frozen up;
N.B: Afterwards switch the appliance off, then on.
Waste water not pumped out.
Check whether:
the drain hose is correctly installed
(see “Installation Instructions”);
the filter is blocked.
the drain hose is frozen up.
the “Rinse hold” button is pressed.
Detergent and additive product residues in
dispenser at end of wash.
Check whether:
the siphon is correctly installed and clean
(see “Care and Maintenance”);
enough water is being supplied. The mesh filters
between the inlet hose and the tap could be clogged
(see “Care and Maintenance”). Check and clean the
filter two or three times a year (see “Removing the
filter”).
Also see “Detergent and Additives” for information.
The appliance vibrates during the spin cycle.
Check whether:
the appliance is levelled and solidly installed on all
four feet (see “Installation Instructions”);
the transit bolts have been removed. The transit
bolts must be removed before the appliance can be
used (see “Installation Instructions”).
Water Stop fault (depending on model)
When the appliance detects a water leakage the pump
runs continuously.
Switch off the appliance, unplug it and make sure that
the water tap is closed.
The “Water Stop” may have been triggered by:
1.
too much foam;
2.
leakage in the inlet hose or in the appliance.
Tilt the appliance forwards carefully to allow the
collected water to flow out from the bottom of the
appliance. Then:
1.
connect the appliance to the electrical outlet,
2.
open the tap,
3.
reselect the desidered programme and press the
“On/Off” button.
Important:
if the fault occurs again, call After-Sales
Service with details about the fault (see “After-Sales
Service”).
Final spin results are poor:
The appliance has an imbalance detection and
correction system. If individual heavy articles are
loaded (bathmat, bathrobe, etc.) this system may
reduce the spin speed automatically to protect the
appliance or even interrupt the spin cycle altogether,
if the imbalance is too great even after several spin
starts.
if the laundry is still too wet at the end of the cycle,
add smaller articles of laundry to balance the load
and repeat the spin cycle.
excessive foam formation may prevent spinning.
Ensure correct amount of detergent is used
Important:
this machine is fitted with a safety system.
The programme is interrupted after a few minutes if
one of the following happens:
no water supply;
pump blocked.
If the pump is blocked, switch off the appliance and
clean the pump (see “Removing the filter”). Then re-
start the appliance.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Whirlpool awm 510 ix at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Whirlpool awm 510 ix in the language / languages: English as an attachment in your email.

The manual is 0,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info