366791
4
Zoom out
Zoom in
Previous page
1/19
Next page
4
BEFORE USING THE WASHING MACHINE
1.Removing the packaging and check
After unpacking, make sure that the washing
machine is undamaged. If in doubt, do not use
the washing machine. Contact After-Sales
Service or your local retailer.
Keep the packaging materials (plastic bags,
polystyrene parts, etc.) out of reach of children,
as they are potentially dangerous.
2.Remove the transit bolts
The appliance is fitted with transit bolts to
prevent internal damage during transport.
Before using the washing machine you must
remove the transit bolts
(see “Installation/
Remove the transit bolts”).
3.Install the washing machine
Remove the protective foil from the control panel.
Move the machine without carrying it at the top.
Install the appliance on a solid and level floor
surface, preferably in a corner of the room.
Adjust the feet to ensure that the machine is
stable and level (see “Installation / Adjust the
feet”).
4.Water supply
Connect the water supply inlet hose in
accordance with regulations of your local water
company (see “Installation/Connect the water
inlet hose”).
Water supply: cold water only
Tap: 3/4” threaded hose connection
Pressure: 100-1000 kPa (1-10 bar).
For Great Britain & Ireland only:
Water inlet: hot and cold fill.
The warm water inlet temperature must not
exceed 60°C.
5.Drain hose
Connect the drain hose to the siphon or hook it
over the edge of a sink by means of the “U” bend
(see “Installation/Connect the water drain hose”).
If the washing machine is connected to a built-in
drainage system, ensure the latter is equipped with
a vent to avoid simultaneous loading and draining
of water (siphoning effect).
6.Electrical connections
Electrical connections must be carried out by a
qualified technician in compliance with the
manufacturer’s instructions and current standard
safety regulations.
Voltage information, power consumption and
electrical protection data are supplied on the
inside of the appliance door.
The appliance must be connected to the mains
exclusively by means of a socket with an earth
connection in accordance with established
regulations. The appliance must be earthed by
law. The manufacturer declines all liability for
damage to property or injury to persons or
animals deriving either directly or indirectly
from failure to observe the directions.
Do not use extension leads or multi sockets.
Before any maintenance on the washing
machine disconnect it from the mains supply.
Access to the mains plug or to disconnection
from mains supply via a double-pole switch must
be ensured at all times following the
installation.
Do not operate the washing machine if it has
been damaged during transport. Inform the
After-Sales Service.
Mains cable replacement is only to be carried out
by After-Sales Service.
The washing machine must only be used in the
household for the prescribed uses.
Minimum housing dimensions:
Width: 600 mm
Height: 825 mm
Depth: 600 mm
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Whirlpool awm 510 ix at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Whirlpool awm 510 ix in the language / languages: English as an attachment in your email.

The manual is 0,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info