70489
2
Zoom out
Zoom in
Previous page
1/2
Next page
Whirlpool is a registered trademark of Whirlpool USA
5019 312 10450
Prewash cycle increases programme duration approximately 15 min. Consumption values were measured in normalized
conditions in compliance with standard IEC/EN 60 456. Consumption data in the home may vary with respect to the
values in the table in relation to the water supply pressure and temperature, the load and the type of wash.
The data on the “Energy Label” refer to the programme “Cotton 60°C”.
* To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains
the water out.
1. Load the machine, close the drum doors and
check that they are properly locked.
2. Add detergents and additives into the dispenser to
no more than the “MAX” level mark, as follows:
Programme with pre and main wash
Main wash programme without prewash
Fabric softeners and conditioners
Chlorine bleach
Stain remover agents
Anti-scale agents (if necessary)
3. Press the “On/Off” button.
The lamp of the “Start” button flashes.
4. Turn the programme selector knob to the
desired programme. The lamp of the
programme’s standard spin speed lights up.
Selecting or deselecting an option can be done
at any time during the programme. The option
will be applied as long as the corresponding
programme phase has not been executed yet.
“Eco” button
The duration of the wash is extended and the
max temperature reduced to save up to 40% of
energy compared to a normal wash but
maintaining good washing results.
“Easy Ironing” button
Can be used together with “Cotton”, “Synthetic”
and “Daily Mixed” programmes to make ironing
easier.
Increases the water quantity in rinsing and the
clothes are spun in a softer manner.
“Intensive Rinse” button
The amount of water is increased to ensure a
more intensive rinse.
This option is particularly suitable for areas with
very soft water, washing baby linen and people
with skin allergies.
“Rinse Hold” button
The laundry remains in the last rinse water without
progressing to the final spin cycle to avoid creasing
and prevent colours from fading.
This option is particularly recommended for the
“Synthetic” , “Delicate” and “Daily
Mixed ” programmes.
This function is particularly useful if you want to
postpone spinning to a later time, or if you want
to drain only.
As soon as the appliance stops in the rinse hold,
the lamp of the “Start” button flashes.
CONSUMPTION DATA
Programme
Temperature Selector
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approx. Programme
Duration
(hours : minutes)
Cotton 95 5.0 66* 1.85 2:05
Cotton 60 5.0 55 0.95 2:05
Cotton 40 5.0 55 0.60 2:05
Daily Mixed 40 3.0 49 0.48 1:00
Synthetic 60 2.0 56 0.80 1:30
Synthetic 40 2.0 56 0.45 1:20
Delicate 40 1.5 60 0.60 0:45
Wool 40 1.0 60 0.50 0:40
Handwash 30 1.0 60 0.30 0:50
PREPARATION OF WASH CYCLE
SELECT THE DESIRED OPTION
Appliance in “Rinse Hold”:
Press the “Rinse Hold” button or the flashing
“Start” button: the programme will terminate
automatically with the selected spin cycle.
If you do not wish to spin the clothes, turn the
programme selector knob to the “Drain
programme and press the “Start” button again.
Spin Speed selection button
Every programme has an automatically preset
spin speed.
Press the button to set another spin speed.
If spin speed “0” is selected, the final spin is
cancelled and the programme ends with a drain
cycle.
The “Start Delay” button allows the user to run
the machine at his convenience, for example at
night when electricity is cheaper.
Select programme, spin speed and options.
Press the “Start Delay” button several times to
select a delay time of 1, 3, 6, 9 or 12 hours.
The corresponding indicator lamp flashes.
Start the programme (see next paragraph).
As the delay time decreases, the
corresponding indicator lamp flashes.
The flashing light of the delay indicator lamp
goes out when the programm starts.
The delay time can still be modified after the
“Start” button has been pressed:
To decrease the delay time
(Repeatedly) press the “Start Delay” button.
Note, however, that the selected wash
programme starts IMMEDIATELY as soon as you
push “Start Delay” with the “1h” lamp flashing.
To increase the delay time
Switch the washing machine off by pushing the
“On/Off button.
Turn the programme selector to a different
programme.
Switch the washing machine on again by
pressing the “On/Offbutton.
Reselect the desired programme and options.
Select the desired delay time by (repeatedly)
pressing the “Start Delay” button. Press the
“Start” button.
Verify that the appliance is switched on.
Turn on the tap and press the “Start” button.
The indicator lamp of the “Start” button stops
flashing and lights up.
Note: If there is a power interruption or if the
appliance is disconnected during the cycle, the
programme will run again from the point where it
was interrupted.
The “End” lamp of the programme sequence
indicator lights up.
1. Press the “On/Off” button to switch off the
machine.
2. Turn the tap off.
3. Wait for the lid to unlock (about 1 minute).
4.
Open the lid and the drum doors and unload
the machine. Leave the lid open for some time
to allow the inside of the appliance to dry
.
1. Switch the appliance off by pressing “On/Off”.
2. Turn the programme selector knob to the new
programme.
3. Switch the appliance on again by pressing
“On/Off”. The “Start” button flashes. If
necessary, select additional options and
different spin speed.
4. Start programme by pressing the “Start” button.
If, for any reason, you wish to interrupt the
programme for a certain time and continue it later:
1. Press the “On/Off” button.
2. After the desired pause, press again on the
“On/Off” button.
1. Switch off the appliance by pressing “On/Off”.
2. Turn the programme selector to “Drain” .
3. Switch the appliance on again by pressing
“On/Off”. The lamp of the “Start” button
flashes.
4. Press the “Start” button to start the “Drain”
programme.
START DELAY
PROGRAMME START
END OF WASH CYCLE
CHANGE THE PROGRAMME DURING
THE WASH CYCLE
PAUSE/INTERRUPT A PROGRAMME
CANCEL PROGRAMME
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Whirlpool AWE 6722 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Whirlpool AWE 6722 in the language / languages: English as an attachment in your email.

The manual is 0,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Whirlpool AWE 6722

Whirlpool AWE 6722 User Manual - English - 17 pages

Whirlpool AWE 6722 Quick start guide - German - 2 pages

Whirlpool AWE 6722 User Manual - German - 16 pages

Whirlpool AWE 6722 Quick start guide - Dutch - 2 pages

Whirlpool AWE 6722 User Manual - Dutch - 16 pages

Whirlpool AWE 6722 Quick start guide - French - 2 pages

Whirlpool AWE 6722 User Manual - French - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info