70489
12
Zoom out
Zoom in
Previous page
1/17
Next page
GB 12
What should I do when the automatic safety system detects a malfunction?
The programme is interrupted and various indicators (depending on model) point to the source of the fault.
Fault description table.
a.
*
Water inlet fault (no or insufficient water
supply)
Switch off the washing machine by pressing the
“On/Off
button and unplug it.
Check whether:
the water tap is fully turned on, and the water
supply pressure is sufficient.
the water inlet hose is kinked.
the mesh filter in the water inlet hose is blocked
(see “Care and maintenance”).
the water in the water inlet hose is frozen.
the washing machine has a safety hose and the
safety valve is open (red indicator in the safety
valve inspection window). In this case replace it
with a new safety hose.
Reconnect the washing machine.
Press the
“On/Off”
and the
“Start”
button to
continue with the programme (do not add
detergent for this programme).
If the fault re-occurs, contact After-Sales (see
After-Sales Service”).
b.
*
Draining out fault
Switch off the washing machine by pressing the
“On/Off
button and unplug it.
Check whether:
the drain hose is kinked (see “Installation”).
the pump impeller is obstructed (see “Cleaning
the foreign body trap”).
the water in the drain hose is frozen.
If water has remained in the drum, you can drain it
by following the instructions in the chapter
“Draining residual water”.
IMPORTANT:
Before draining, allow the wash
water to cool down.
Reconnect the washing machine.
Press the
“On/Off”
and the
“Start”
button to
continue with the programme (do not add
detergent for this programme).
If the fault re-occurs, contact After-Sales Service
(see “After-Sales Service”).
c.
*
Electrical module fault
Switch the washing machine off. Switch it on again
by pressing the
“On/Off”
button.
If the fault re-occurs, contact After-Sales Service
(see “After-Sales Service”).
d.
*
Water stop fault
(depending on model)
In addition to the fault indicators the pump operates.
The “Water Stop“ fault may have been
triggered by:
1.
Too much foam.
2.
A leak in the inlet hose or in the washing machine.
Switch the washing machine off by pressing the
“On/Off”
button, unplug the washing machine and
turn off the water tap.
Tilt the washing machine forwards carefully to
allow the water to evacuate from the bottom tray.
Then:
1.
Reconnect the washing machine.
2.
Turn on water supply (if
“On/Off”
button is not
pressed, but the machine begins to fill, turn off the
water supply tap and contact After-Sales Service).
3.
Press the
“On/Off”
button. Reselect the desired
programme, add detergent, if necessary, and
press the
“Start”
button to restart the
programme.
If the fault occurs again, contact After-Sales Service
(see “After-Sales Service”).
e.*Foam detection
Too much foam may interrupt the washing programme.
1.
Switch the washing machine off by pressing the
“On/Off” button.
2.
Move the programme selector to the “Drain”
programme.
3.
Switch the washing machine on again and press
the
“Start”
button.
4.
After the drain programme is finished, start the
original washing programme again, but avoid
excessive detergent dosing.
The spin speed indicator lamps are flashing Fault description
1st (“0”) “Water inlet fault”
1st (“0”) + 2nd “Draining fault”
Other combinations “Electrical components fault”
1st (“0”) + 4th “Water Stop fault”
3rd “Foam detection / overdosing of detergent”
IFU_Alpha_electr_gb.fm Page 12 Wednesday, March 30, 2005 9:32 AM
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Whirlpool AWE 6722 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Whirlpool AWE 6722 in the language / languages: English as an attachment in your email.

The manual is 1,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Whirlpool AWE 6722

Whirlpool AWE 6722 Quick start guide - English - 2 pages

Whirlpool AWE 6722 Quick start guide - German - 2 pages

Whirlpool AWE 6722 User Manual - German - 16 pages

Whirlpool AWE 6722 Quick start guide - Dutch - 2 pages

Whirlpool AWE 6722 User Manual - Dutch - 16 pages

Whirlpool AWE 6722 Quick start guide - French - 2 pages

Whirlpool AWE 6722 User Manual - French - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info