314372
12
Zoom out
Zoom in
Previous page
1/18
Next page
GB 12
Washing machine exterior and control
panel
Clean with a soft damp cloth.
If necessary, a neutral household cleaner can be
applied (do not use aggressive or abrasive products).
Lid seal
Clean from time to time with a damp cloth.
Water inlet hose(s)
Check the hose regularly for brittleness and
cracks. Replace if necessary.
TROUBLESHOOTING GUIDE
This washing machine is equipped with automatic
safety functions which detect and diagnose faults at
an early stage and allow you to react appropriately.
Often, however, the faults detected are small
enough to be solved in a matter of minutes.
For example:
*The washing machine does not start, no
lamp lights up.
Check whether:
the washing machine is plugged in.
the wall socket is functioning correctly
(use a table lamp or similar).
the
“On/Off”
button is pressed.
*The washing machine does not start, but
the pilot light is on and the “Start” lamp
is flashing.
Check whether:
the programme has been changed.
Press the “Start” button again.
*The washing machine does not start, but
the pilot light and the “Start” lamp are
on.
Check whether:
the washing machine lid is properly closed. Open
and close it again.
*The washing machine stops during the
programme.
Check whether:
the “Rinse Hold” button is pressed: terminate
this option by pressing the button again.
the programme has been changed. Reselect the
desired programme and press the
“Start”
button.
the programme has not been started (the “Start”
lamp is flashing). Press the
“Start”
button.
the safety system of the washing machine was
activated. See fault description table.
*Detergent and additive product
residues in dispenser at end of wash.
Check whether:
the detergent dispenser is properly installed and
is not blocked (see “Care and maintenance”).
the foreign body trap in the water inlet hose is
not blocked (see “Care and maintenance”).
*The washing machine vibrates during
the spin cycle.
Check whether:
the washing machine is levelled and that all the feet
are adjusted (see “Installation”).
the transport bracket has been removed. Before
starting up the washing machine, the transport
screws and the transport bracket MUST be
removed (see “Installation”).
*Final spin results are poor.
Note:
The washing machine has an unbalance
detection and correction system. If individual heavy
items are loaded (a bathrobe, for example), this
system may reduce the spin speed automatically or
interrupt the spin if it detects too great an
unbalance at the start of the spin, in order to
protect the washing machine.
Check whether:
the pump impeller is obstructed (see “Cleaning
the foreign body trap”).
if the laundry is still too wet at the end of the
programme: possibly add other items of clothing
and repeat the spin cycle.
there is foam on the wash: repeat a rinse-spin
cycle to eliminate excess of detergent.
Excessive foam formation may also prevent
spinning.
3GB10242.fm Page 12 Friday, March 12, 2004 6:34 PM
Black process 45.0° 100.0 LPI
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Whirlpool awa 6122 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Whirlpool awa 6122 in the language / languages: English as an attachment in your email.

The manual is 0,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info