314372
8
Zoom out
Zoom in
Previous page
1/18
Next page
GB 8
PROGRAMME SELECTION
Preparation of wash cycle
1.
Load the machine, close the drum flaps and check that they are properly locked.
2.
Add detergents and additives into the dispenser to no more than the
“MAX”
level mark. Please refer
to “Detergents and additives”.
Select the programme
1.
Press the
“On/Off”
button. The pilot lamp of the
“On/Off”
button, a spin speed indicator lamp and,
in case of availability, a temperature indicator lamp light up.
2.
Turn the programme selector knob to the desired programme and temperature. Select the desired
options as described in the Programme Chart.
The knob will move half a step for correct positioning. The temperature indicator lamp (if
available) switches to the selected temperature.
Start delay (if available)
The “Start Delay” button allows the user to run the machine at his convenience, for example at night
when electricity is cheaper.
Select programme and temperature, spin speed and options.
Press the “Start Delay” button several times to select a delay time of 1, 3, 6, 9 or 12 hours. The
corresponding indicator lamp lights up.
Start the programme (see below). With decreasing delay time the corresponding indicator lamp lights up.
The time delay indicator lamp disappears when the programme starts.
To decrease the delay time or cancel “Start Delay option
(Repeatedly) press the “Start Delay” button.
To increase the delay time
Turn the programme selector to the “Stop” position.
Reselect the desired programme and options. Select the desired delay time by (repeatedly) pressing
the “Start Delay” button. Press the
“Start”
button.
Programme start
Turn on the tap and press the
“Start”
button. The indicator lamp of the
“Start”
button lights up.
Note
: If there is a power interruption or if the washing machine is disconnected during the cycle, the
programme will run again from the point where it was interrupted.
End of wash cycle
The programme selector knob is in the “Stop” position “O”.
1.
Press the
“On/Off”
button to switch off the machine.
2.
Turn the tap off.
3.
Wait for the lid to unlock (about 1 minute).
4.
Open the lid and the drum flaps and unload the machine.
Change the programme during the wash cycle
1.
Turn the programme selector knob to the new programme.
The programme selector knob moves
half a step and the pilot lamp of the “Start” button flashes.
If necessary, select the additional
options and the spin speed.
2.
Start programme by pressing the
“Start”
button.
Pause/Interrupt a programme
If, for any reason, you wish to interrupt the programme for a certain time and continue it later:
1.
Press the
“On/Off”
button.
2.
After the desired pause, press again on the
“On/Off”
button.
Cancel programme
1.
Set the programme selector to “Drain”.
2.
Press the
“Start”
button to start the “Drain” programme.
3GB10242.fm Page 8 Friday, March 12, 2004 6:34 PM
Black process 45.0° 100.0 LPI
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Whirlpool awa 6122 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Whirlpool awa 6122 in the language / languages: English as an attachment in your email.

The manual is 0,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info