315150
3
Zoom out
Zoom in
Previous page
1/17
Next page
CONTENTS
BEFORE USING THE WASHING MACHINE
FIRST WASH CYCLE
PRECAUTIONS AND GENERAL RECOMMENDATIONS
DESCRIPTION OF THE WASHING MACHINE
PREPARATION OF THE WASHING
DETERGENTS AND ADDITIVES
PROGRAMME SELECTION
CLEANING THE FOREIGN BODY TRAP
DRAINING RESIDUAL WATER
CARE AND MAINTENANCE
TROUBLESHOOTING GUIDE
AFTER-SALES SERVICE
TRANSPORT AND HANDLING
INSTALLATION
19
BEFORE USING THE WASHING MACHINE
1.Remove the packaging and check
a.
Cut and remove the shrink-wrap.
b.
Remove the top protection and the protective
corners.
c.
Remove the bottom protection by tilting and
turning the washing machine on one rear bottom
corner.
d.
Open the lid by pressing it slightly down while
raising the handle. Remove the polystyrene
cushion.
e.
Remove the blue protective film from the panel
(depending on model).
After unpacking, make sure that the washing
machine is undamaged. If in doubt, do not use
the washing machine. Contact After-Sales
Service or your local retailer.
Keep the packaging materials (plastic bags,
polystyrene parts, etc.) out of reach of children;
they are potentially dangerous.
2.Remove the transport bracket
The washing machine is fitted with transport
screws and a transport bracket to prevent
damage during transport.
Before using the
washing machine you must remove the
transport bracket
(see “Installation/Remove
the transport bracket”).
3.Install the washing machine
Place the washing machine on a flat and stable
floor surface.
Adjust the feet to ensure that the machine is
stable and level (see “Installation/Adjust the
feet”).
4.Water supply
Connect the water supply inlet hose in
accordance with the regulations of your local
water company (see “Installation/Connect the
water inlet hose”).
Water supply: Cold water only
Tap: 3/4” threaded hose connection
Pressure: 100-1000 kPa (1-10 bar).
5.Drain hose
Connect the drain hose to the siphon or hook it
over the edge of a sink with the “U” bend (see
“Installation/Connect the water drain hose”).
If the washing machine is connected to a built-
in drainage system, ensure the latter is equipped
with a vent to avoid simultaneous loading and
draining of water (siphoning effect).
6.Electrical connection
Electrical connections must be carried out by a
qualified technician in compliance with the
manufacturer’s instructions and the current
standard safety regulations.
The technical data (voltage, power and fuses)
are given on the rating plate on the rear of the
washing machine.
The washing machine must be connected
exclusively by means of a socket with an earth
connection in accordance with current regulations.
The washing machine must be earthed by law. The
manufacturer declines all liability for damage to
persons or property deriving directly or indirectly
from failure to observe the directions.
Do not use extension leads or multi sockets.
Before any maintenance on the washing
machine disconnect it from the mains supply.
Access to the mains plug or to disconnection
from the mains supply via a double-pole switch
must be ensured at all times following the
installation.
Do not operate the washing machine if it has
been damaged during transport. Inform the
After-Sales Service.
Mains cable replacement is only to be carried out
by After-Sales Service.
The washing machine must be connected to an
effective earthing installation, in compliance with
the regulations in force. In particular, washing
machines installed in premises containing a shower
or a bath must be protected by a differential residual
current device of at least 30 mA. Earthing the
washing machine is obligatory under the law. The
manufacturer declines all liability for damage to
persons or property deriving either directly or
indirectly from failure to observe the directions
above.
The washing machine may only be used in the
household for the prescribed uses.
Dimensions:
Width: 400 mm
Height: 900 mm
Depth: 600 mm
20
FIRST WASH CYCLE
PRECAUTIONS AND GENERAL RECOMMENDATIONS
1.Packing
The packaging materials are 100% recyclable and
bear the recycling symbol . Adhere to local
regulations when disposing of packaging material.
2.Energy saving tips
Achieve the best use of energy, water, detergent
and time by using the recommended maximum
load size.
Do not exceed the detergent dosages indicated
in the manufacturer’s instructions.
The Eco Ball - a special system in the outlet - will
prevent detergent loss from the drum to avoid
detergent loss into the environment.
Use “Prewash” for heavily soiled laundry only!
Save detergent, time, water and energy
consumption by not selecting “Prewash” for
slight to normally soiled laundry.
Pretreat stains with stain remover or soak dried
in stains in water before washing to reduce the
necessity of a hot wash program.
Save energy by using a 60° C instead of a 90° C
wash programme or a 40° C instead of a 60° C
wash programme.
Save energy and time by selecting a high spin
speed to reduce the water content in laundry
before using a tumble dryer (for machines with
adjustable spin speed).
3.Disposing of packaging and old washing
machines
The washing machine is built from reusable
materials. The washing machine must be
disposed of in compliance with current local
waste disposal regulations.
Before scrapping, cut of the power cable so that the
washing machine cannot be connected to the mains.
Remove detergent from compartment if you
intend scrapping your washing machine.
4.Child safety
Children must not be allowed to play with or in
the washing machine.
5.General recommendations
Do not leave the washing machine connected
when not in use. Turn off the tap.
Before cleaning or carrying out maintenance
switch off the washing machine and disconnect
it from the mains supply.
To clean the outside of the washing machine,
use a neutral detergent and a damp cloth.
Do not use abrasive detergents.
Do not attempt to force the lid open.
If necessary, the power cable may be replaced
with an identical one obtained from our After-
Sales Service. The power cable must only be
replaced by a qualified technician.
6.EC Declaration of Conformity
This washing machine has been designed,
constructed and distributed in compliance with
the safety requirements of EC Directives:
73/23/EEC Low Voltage Directive
89/336/EEC EMC Directive
93/68/EEC CE Marking Directive
We recommend that the first wash cycle be carried out empty. This will remove any residual water used
in the factory checks.
1.
Turn on the tap.
2.
Close the drum flaps.
3.
Pour a small amount of detergent (about 30 ml) into the detergent dispenser .
4.
Press the
“On/Off”
button.
5.
Select a short programme (see programme chart).
6.
Press the
“Start”
button.
21
DESCRIPTION OF THE WASHING MACHINE
PREPARATION OF THE WASHING
Sort the laundry
1.
Sort the laundry according to…
Type of fabric / care label symbol
Cottons, mixed fibres, easy care/synthetics,
wool, handwashed items.
Colour
Separate whites and coloureds. Wash new
coloured items separately.
Size
Wash items of different sizes in the same load to
improve efficiency and distribution in the drum.
Fabric delicacy
Wash delicate articles separately: use a special
programme for Pure New Wool , curtains and
other delicates. Always remove curtain glides or
wash curtains with the glides inside a cotton bag.
Use the special program for handwash fabrics. Wash
stockings, belts and other small items or articles
with hooks (e.g. bras) in special cotton bags for
washing machines or in zipped pillow cases.
2.
Empty pockets
Coins, safety pins and similar items can damage
your washing machine drum and tub.
3.
Fasteners
Close zips and fasten buttons or hooks; loose
belts or ribbons should be tied together.
1.
Lid
2.
Detergent dispenser
3.
Drum flaps
To open the drum press the
small flap and hold the large
flap.
4.
Pump and foreign body trap
5.
After-Sales Service sticker
(behind the foreign body trap
cover)
6.
Mobility lever (depending on
model)
To move the washing machine:
pull the handle out a little bit
by hand and pull it out to the
stop with the foot.
7.
Adjustable feet
22
Stain removal
Blood, milk, egg and other organic substances
are generally removed by the enzyme phase of
the programme.
To remove red wine, coffee, tea, grass and fruit
stains etc. add a stain removing agent in
detergents dispenser compartment or chlorine
bleach in compartment (depending on model).
Particularly stubborn stains should be treated
before the wash.
Dyeing and bleaching
Products usually consist of dye colour, fixing agent
and salt. Pour the dye colour, the fixing agent and
then the salt directly into the empty drum. Load
the laundry only afterwards.
Only use dyes and bleaches recommended for
washing machines.
Follow the manufacturer’s instructions.
Plastic and rubber parts of the machine may be
stained by dyes or bleaches.
Starching
Dissolve/dilute the starch, powder or liquid, in
approximately 1 litre water outside of the washing
machine in a small container. Load the washing
machine, close the drum flaps and pour the dissolved
starch directly on the drum. Then close the lid, select
the programme “Rinse and Spin” and start.
Loading the laundry
1.
Open the machine lid.
2.
Open the drum by pressing the small flap and holding
the large flap.
3.
Place the items of laundry in the drum one by one
without compressing them. Follow loads
recommended in the “programme chart”: overloading
will result in unsatisfactory washing results and
creased laundry.
4. Close the drum flaps and check that they are
properly locked.
1
2
3
23
DETERGENTS AND ADDITIVES
Choice of the right detergents and additives
The type of detergent depends on:
type of fabric (cottons, easy care/synthetics,
delicate items, wool).
Note:
use only specific detergents for wool.
colour;
washing temperature;
degree and type of soiling.
Notes:
Whitish residues on dark fabrics are caused by
insoluble detergents components used in modern
phosphate-free powder detergents. If you notice
this problem, shake or brush the affected items or
use a liquid detergents.
Keep detergents and additives in a dry place and
out of reach of children.
Use only detergents and additives specifically
produced for domestic washing machines.
If you use descaling agents, dyes or bleaches,
make sure they are suitable for washing machine
use. Descaler could contain components that can
attack parts of your washing machine.
Do not use solvents (turpentine, benzine, etc.).
Do not machine wash fabrics that have been
treated with solvents or flammable liquids.
Dosage
Follow the instructions on the detergent pack in
relation to:
the degree and type of soiling;
the size of the load;
-
full load: follow the detergent manufacturer’s
instructions;
-
half load: 3/4 the amount used for a full load;
-
minimum load (about 1 kg): half the amount
used for a full load;
water hardness in your area (ask for information
from your water company): soft water requires
less detergent than hard water.
Notes:
Too much detergent can result in excess foam
formation, and the reduction of washing efficiency.
If the washing machine detects excessive foam it
may prevent spinning.
Insufficient detergent may result in:
grey laundry, deposits on the drum, tub and heater.
When using concentrated fabric softeners, add water in
the detergents dispenser up to “MAX” level mark.
To prevent dispensing problems when using highly
concentrated powder and liquid detergents, use
the special detergent ball or bag supplied with the
detergent and place it inside the drum.
WATER HARDNESS CHART
WATER HARDNESS
CATEGORY
CHARACTERISTICS GERMAN
°dH
FRENCH
°fH
ENGLISH
°eH
1
2
3
4
soft
medium
hard
very hard
0-7
7-14
14-21
over 21
0-12
12-25
25-37
over 37
0-9
9-17
17-26
over 26
Filling up with detergents and additives
The dispenser will have three or four compartments depending on model.
Pour in the detergent:
Washing powder for prewash and main wash
Washing powder for main wash without prewash
Fabric softeners and starch products,
no more than to “
MAX
” mark.
Chlorine bleach, no more than to “
MAX
” mark.
(only four compartments model)
Stain removers
Water softeners (water hardness class 4)
Starch (dissolved in water)
Be careful not to fill more than the “
MAX
” level mark.
Do not use liquid detergents for programmes with prewash.
For programmes without prewash and temperatures from cold to
40° C, it is recommended to use liquid detergents to avoid whitish
residues on the laundry.
24
PROGRAMME SELECTION
Preparation of wash cycle
1.
Load the machine, close the drum flaps and check that they are properly locked.
2.
Add detergents and additives into the dispenser to no more then the
“MAX“
level mark. Please refer
to “Detergents and additives”.
3.
Press the
“On/Off“
button. The pilot lamp of the
“On/Off“
button, a spin speed indicator lamp and,
in case of availability, a temperature indicator lamp light up.
4.
Turn the programme selector knob to the desired programme and temperature. Select the desired options as
described in the Programme Chart.
The knob will move half a step for correct positioning. The temperature indicator lamp (if available)
switches to the selected temperature.
Start delay (if available)
The “Start Delay” button allows the user to run the machine at his convenience, for example at night
when electricity is cheaper.
Select programme and temperature, spin speed and options.
Press the “Start Delay” button several times to select a delay time of 1, 3, 6, 9 or 12 hours. The
corresponding indicator lamp lights up.
Start the programme (see below). With decreasing delay time the corresponding indicator lamp lights up.
The time delay indicator lamp disappears when the programme starts.
To decrease the delay time or cancel “Start Delay” option
(Repeatedly) press the “Start Delay” button.
To increase the delay time
Turn the programme selector to the “Stop” position.
Reselect the desired programme and options. Select the desired delay time by (repeatedly) pressing
the “Start Delay” button. Press the
“Start”
button.
Programme start
Turn on the tap and press the
“Start”
button. The indicator lamp of the
“Start”
button lights up.
Note
: If there is a power interruption or if the washing machine is disconnected during the cycle, the
programme will run again from the point where it was interrupted.
End of wash cycle
The programme selector knob is in the “Stop” position “O”.
1.
Press the
“On/Off”
button to switch off the machine.
2.
Turn the tap off.
3.
Wait for the lid to unlock (about 1 minute).
4.
Open the lid and the drum flaps and unload the machine.
Change the programme during the wash cycle
1.
Turn the programme selector knob to the new programme.
The programme selector knob moves half
a step and the pilot lamp of the “Start” button flashes.
If necessary, select the additional options
and the spin speed.
2.
Start programme by pressing the
“Start”
button.
Pause/Interrupt a programme
If, for any reason, you wish to interrupt the programme for a certain time and continue it later:
1.
Press the
“On/Off”
button.
2.
After the desired pause, press again on the
“On/Off”
button.
Cancel programme
1.
Set the programme selector to “Drain”.
2.
Press the
“Start”
button to start the “Drain” programme.
25
CLEANING THE FOREIGN BODY TRAP
The washing machine is provided with a self-cleaning
pump. The foreign body trap keeps objects like buttons,
coins, safety-pins etc. which have been left in the
laundry.
1.
Unplug the washing machine.
2.
Open the foreign body trap cover with a coin.
3.
Place a bowl beneath it.
4.
Turn the foreign body trap slowly anti-clockwise until
the grip is vertical; do not remove it as yet.
5.
Wait until all the water has drained out.
6.
Now unscrew the foreign body trap completely and
extract it.
7.
Remove any foreign items from the foreign body trap.
8.
Make sure the pump impeller (in the housing behind
the foreign body trap) is not obstructed.
9. Insert the foreign body trap again and screw it fully
down in a clockwise direction to the stop (until the
grip is horizontal).
10.
Pour 0.5 litres of water into the machine via the drum
and check that water does not leak from the foreign
body trap.
11.
Close the foreign body trap cover.
12.
Reconnect the washing machine.
Check the foreign body trap if the washing machine is not
draining correctly or if it fails to perform spin cycles.
Check the foreign body trap regularly, two or three times
a year and clean it if necessary.
IMPORTANT:
Make sure the water has cooled before
emptying the foreign body trap.
26
DRAINING RESIDUAL WATER
CARE AND MAINTENANCE
When should I drain residual water (draining problem)?
Before transporting (moving) the machine.
If the washing machine is installed in a room subject to sub-
zero temperatures. It is best in this case to drain the machine
after every wash.
If the draining problem indicators are flashing (see
“Troubleshooting Guide”)
1.
Stop the washing machine and unplug it.
2.
Turn off the tap, disconnect the water supply hose from the
machine and allow the water to drain into a basin.
3.
Open the foreign body trap, let the water drain into a small
shallow basin and close the trap.
4.
Release the drain hose then open the fixing clip located at the
rear of the machine (see arrow A).
5.
Let the residual water flow into a shallow basin.
6.
Wait until the flow stops.
7.
Fix the drain hose again with the clip and replace it with the
U-bend.
8.
Reconnect the water supply hose and the power plug.
Important:
After draining the residual water, screw on the machine’s
water supply hose by hand. Check water-tightness of washing
machine connections by turning the tap completely on.
Detergent dispenser
1.
Push in the buttons on each side of the dispenser.
2.
Pull the dispenser towards you and remove.
A small quantity of water can remain in the dispenser. It is
advisable to carry the dispenser in an upright position.
3.
Wash the dispenser using running water.
You can also remove the siphon caps in the dispenser for
cleaning.
4.
Replace the siphon caps in the dispenser (if removed).
Make sure that they lock in place.
5.
Replace the dispenser by locating the bottom tabs in the lid
holes and pivot until both of the upper buttons lock.
Note: ensure that the detergent dispenser is correctly
reinstalled.
27
Water inlet hose filter
Check and clean regularly (at least two or three times a year).
1.
Unplug the washing machine.
2.
Turn off the tap.
3.
Unscrew the hose from the tap.
4.
Carefully clean the filter located at the end of hose, without
assembling it, for example with a tooth-brush.
Note
: For machines equipped with hose type “
A
”, it must not
be submerged in water.
5.
Screw the flexible hose back onto the tap by hand. Do not use
pliers (risk of squashing the joint).
6.Turn on the tap and check that the connections are water-tight.
7.
Plug the washing machine back in.
Recovering an object that falls between the drum and
the tub
If an object accidentally falls between the drum and the tub,
you can recover it thanks to one of the removable drum blades:
1.
Unplug the washing machine.
2.
Remove the laundry from the drum.
3.
Close the drum flaps and turn the drum a half-turn.
4.
Using a spanner, press on the plastic end while sliding the
blade from left to right.
5.
It will fall into the drum.
6.
Open the drum: you can recover the object through the hole
in the drum.
7.
Refit the blade from inside the drum:
Position the plastic tip above the hole on the right side of
the drum.
8.
Then slide the plastic blade from right to left until it clips.
9.
Close the drum flaps again, turn the drum through half a
turn and check the positioning of the blade at all its
anchorage points.
10.
Plug the washing machine in again.
A
7
4
3
4
28
Washing machine exterior and control
panel
Clean with a soft damp cloth.
If necessary, a neutral household cleaner can be
applied (do not use aggressive or abrasive products).
Lid seal
Clean from time to time with a damp cloth.
Water inlet hose(s)
Check the hose regularly for brittleness and
cracks. Replace if necessary.
TROUBLESHOOTING GUIDE
This washing machine is equipped with automatic
safety functions which detect and diagnose faults at an
early stage and allow you to react appropriately.
Often, however, the faults detected are small
enough to be solved in a matter of minutes.
For example:
*The washing machine does not start, no
lamp lights up.
Check whether:
the washing machine is plugged in.
the wall socket is functioning correctly
(use a table lamp or similar).
the
“On/Off“
button is pressed.
*The washing machine does not start, but
the pilot light is on and the “Start“ lamp
is flashing.
Check whether:
the programme has been changed.
Press the “Start” button again.
*The washing machine does not start, but
the pilot light and the “Start“ lamp are
on.
Check whether:
the washing machine lid is properly closed. Open
and close it again.
*The washing machine stops during the
programme.
Check whether:
the “Rinse Hold“ button is pressed: terminate
this option by pressing the button again.
the programme has been changed. Reselect the
desired programme and press the
“Start“
button.
the programme has not been started (the “Start”
lamp is flashing). Press the
“Start“
button.
the safety system of the washing machine was
activated. See fault description table.
*Detergent and additive product residues
in dispenser at end of wash.
Check whether:
the detergent dispenser is properly installed and
is not blocked (see “Care and maintenance”).
the foreign body trap in the water inlet hose is
not blocked (see “Care and maintenance”).
*The washing machine vibrates during the
spin cycle.
Check whether:
the washing machine is levelled and that all the
feet are adjusted (see “Installation”).
the transport bracket has been removed. Before
starting up the washing machine, the transport
screws and the transport bracket MUST be
removed (see “Installation”).
*Final spin results are poor.
Note:
The washing machine has an unbalance
detection and correction system. If individual
heavy items are loaded (a bathrobe, for example),
this system may reduce the spin speed
automatically or interrupt the spin if it detects too
great an unbalance at the start of the spin, in order
to protect the washing machine.
Check whether:
the pump impeller is obstructed (see “Cleaning
the foreign body trap”).
if the laundry is still too wet at the end of the
programme: possibly add other items of clothing
and repeat the spin cycle.
there is foam on the wash: repeat a rinse-spin
cycle to eliminate excess of detergent.
Excessive foam formation may also prevent
spinning.
29
What should I do when the automatic safety system detects a malfunction?
The programme is interrupted and various indicators (depending on model) point to the source of the fault.
Fault description table.
a.
*
Water inlet fault (no or insufficient water
supply)
Switch off the washing machine by pressing the
“On/Off”
button and unplug it.
Check whether:
the water tap is fully turned on, and the water
supply pressure is sufficient.
the water inlet hose is kinked.
the mesh filter in the water inlet hose is blocked
(see “Care and maintenance”).
the water in the water inlet hose is frozen.
the washing machine has a safety hose and the
safety valve is open (red indicator in the safety
valve inspection window). In this case replace it
with a new safety hose.
Reconnect the washing machine.
Press the
“On/Off”
button to continue with the
programme (do not add detergent for this
programme).
If the fault re-occurs, contact After-Sales (see
“After-Sales Service”).
b.
*
Draining out fault
Switch off the washing machine by pressing the
“On/Off”
button and unplug it.
Check whether:
the drain hose is kinked (see “Installation”).
the pump impeller is obstructed (see “Cleaning
the foreign body trap”).
the water in the drain hose is frozen.
If water has remained in the drum, you can drain
it by following the instructions in the chapter
“Draining residual water”.
IMPORTANT:
Before draining, allow the wash
water to cool down.
Reconnect the washing machine.
Press the
“On/Off”
button to continue with the
programme (do not add detergent for this
programme).
If the fault re-occurs, contact After-Sales Service
(see “After-Sales Service”).
c.
*
Electrical module fault
Switch the washing machine off. Switch the
washing machine on by pressing the
“On/Off”
button twice.
If the fault re-occurs, contact After-Sales Service
(see “After-Sales Service”).
d.
*
Water stop fault
(depending on model)
In addition to the fault indicators the pump operates.
The “Water Stop“ fault may have been triggered by:
1.
Too much foam.
2.
A leak in the inlet hose or in the washing
machine.
Switch the washing machine off by pressing the
“On/Off“
button, unplug the washing machine
and turn off the water tap.
Tilt the washing machine forwards carefully to
allow the water to evacuate from the bottom tray.
Then:
1.
Reconnect the washing machine.
2.
Turn on water supply (if
“On/Off“
button is not
pressed, but the machine begins to fill, turn off
the water supply tap and contact After-Sales
Service).
3.
Press the
“On/Off”
button. Reselect the desired
programme, add detergent, if necessary, and
press the
“Start“
button to restart the
programme.
If the fault occurs again, contact After-Sales
Service (see “After-Sales Service“).
The pilot lamp of the “Start” button and the
following spin speed indicator lamps are
flashing
Fault description
1st (“0”) “Water inlet fault”
1st (“0”) + 2nd “Draining fault”
Other combinations Electrical components fault”
1st (“0”) + 4th Water Stop fault
30
AFTER-SALES SERVICE
Before contacting After-Sales Service:
1.
Try to remedy the problem yourself (see
“Troubleshooting Guide”).
2.
Restart the programme to check whether the
problem has solved itself.
3.
If the machine continues to function incorrectly,
call After-Sales Service.
Specify:
The nature of the problem.
The exact model of the washing machine.
The service code (number after the word
SERVICE).
The After-Sales Service sticker is in the lid
of the foreign body trap or on the rear of
the machine.
Your full address.
Your telephone number and area code.
As a priority, you should contact the After-Sales
Service of the retailer who supplied you with the
washing machine.
TRANSPORT AND HANDLING
1.
Unplug the washing machine.
2.
Turn off the tap.
3.
Remove the water supply and drain hose.
4.
Eliminate all water from the hoses and the washing
machine (see “Draining residual water”).
Wait for the water to cool so as to avoid any accidents.
5.
To facilitate moving the machine, pull the handle
situated at the bottom front (optional on certain models)
out a little by hand and pull it out to the stop with the
foot. Afterwards push the handle back into the original
stable position.
6.
Fix the transport bracket again for transportation.
7.
Transport the washing machine upright.
IMPORTANT:
Do not use the washing machine while the
handle is pulled out.
31
INSTALLATION
Removal of transport bracket
The washing machine is fitted with a transport bracket to
avoid any possible damage during transport.
Before using the washing machine, the transport bracket
at the back MUST be removed.
1.
Unscrew the two screws
A
and the four screws
B
with a
flat screwdriver or a No. 8 hex nut box spanner.
2.
Remove the transport bracket.
3.
Replace the four outer screws
B
on the machine and
tighten them.
4.
Remove the two seals
C
from the hose holder and clip
them into the openings of the machine
D
.
Note: do not forget to replace and tighten the four outer
screws.
2
1
1
4
C
A
B
D
1
4
D
32
Adjust the feet
Install the washing machine on a level surface, near to
electrical, water and drain connections.
If the floor is uneven, adjust the feet (do not insert pieces
of wood, cardboard etc. under the feet):
1.
Loosen the locknut using the wrench provided.
2.
Adjust the height of the foot by hand.
3.
Retighten the locknut by turning it anti-clockwise.
Make sure that all feet are resting correctly on the floor
and that the washing machine is perfectly level and
stable (use a spirit level).
The washing machine can be installed in an area 40 cm wide
and 63 cm deep.
Note:
if you install the machine on thick carpet, adjust the
feet to ensure that there is sufficient space under the
machine for the air to circulate.
Connect the water inlet hose.
1.
Carefully screw the water inlet hose onto the tap by hand.
2.
Make sure there are no kinks in the hose.
3.
Check water-tightness of tap and washing machine
connections by turning the tap completely on.
If the hose is too short, replace it with a suitable length of
pressure resistant hose (minimum 1000 kPa - EN 50084
approved type).
Periodically check the hose for brittleness and cracks.
Replace if necessary.
The washing machine can be connected without a non-
return valve.
33
Water stop anti-flooding system
(depending on model)
Screw the hose to the water supply tap. Turn the tap fully
on and check the water-tightness of the connection.
The washing machine must not be connected to the
mixing tap of a non-pressurized water heater!
The inlet hose and the plastic enclosure contain
(depending on model) electrical components: do not cut
the hose and do not immerse the enclosure in water.
If the flexible hose is damaged, unplug the washing
machine from the mains immediately, turn off the tap and
replace the hose.
If the flexible hose is too short, replace it with a 3 m Water
Stop hose (available from After-Sales Service or from your
dealer). This operation must be carried out exclusively by a
qualified technician.
Connect the water drain hose
1.
Unhook the drain hose from the left and right hose
connections, see arrow A in figure.
Important:
Do NOT loosen the drain hose connection from the left
side, see arrow B in figure.
Otherwise, there is the risk of
leakage and of scalding with hot water.
2.
Fix the “U” bend (
C
) to the free end of the drain hose.
3.
Connect the drain hose to the siphon or hook it over the
edge of a sink with the “U” bend.
Small hand basins are not suitable.
The edge of the sink must be no more than 100 cm from
the floor.
If you need to add an extension, use a flexible hose of the
same size and secure the unions with screw-on hose clips.
Maximum overall drain hose length: 2.50 m.
Maximum drain height (“U” bend): 100 cm.
Minimum drain height: 55 cm.
Important:
Make sure there are no kinks in the drain hose and take
precautions against it falling while the washing machine is
running.
A
B
C
34
ELECTRICAL CONNECTION
Do not use extension leads or multi sockets.
Electrical connections must be made in accordance with local regulations.
1) Warning - this washing machine must be earthed
This washing machine is normally supplied with a mains lead having a plug fitted in the factory which
has been checked for correct earth continuity.
If the fitted plug is not suitable for your socket outlet, or if the machine’s mains lead is not fitted with
a plug, you should fit a suitable new, good quality plug by following the instructions in (2) below.
Any unsuitable plug should be cut off and disposed of in order to avoid a possible shock hazard should it
be inserted into a socket.
2) CONNECTION TO A REWIRABLE PLUG - to be carried out only by a qualified electrician
The wires in the mains lead are coloured in accordance with the following code:
BLUE - “NEUTRAL” (“N”)
BROWN - “LIVE” (“L”)
GREEN AND YELLOW - “EARTH” (“E”)
To fit a new plug, proceed as follows:
2.1 Polarized Plugs (e.g. 3 pin, 13 amp plug conforming to BS
1363A)
a. The GREEN AND YELLOW wire must be connected to the
terminal in the plug which is marked with the letter “E” or by
the Earth symbol or coloured green and yellow.
b. The BLUE wire must be connected to the terminal which is
marked with the letter “N” or coloured blue.
c. The BROWN wire must be connected to the terminal which is
marked with the letter “L” or coloured brown.
2.2) Non-polarized plugs (e.g. 2 pin with side earth contact)
The wire which is coloured GREEN AND YELLOW must be connected to the earth contact. The other two wires
should be connected to the two pins, irrespective of colour.
FUSE REPLACEMENT
If the mains lead of this washing machine is fitted with a BS 1363A
13 amp fused plug, replace the fuse only with an A.S.T.A. approved
type conforming to BS 1362 and proceed as follows:
Remove the fuse cover (A) and the fuse (B).
Fit the replacement 13 A fuse into the fuse cover.
Refit both into the plug.
For all other types of plug, the supply socket should be protected
by a 16 A fuse or circuit breaker at the distribution board.
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Whirlpool awa 6095 1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Whirlpool awa 6095 1 in the language / languages: English as an attachment in your email.

The manual is 0,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info