573291
11
Zoom out
Zoom in
Previous page
1/12
Next page
GB 10
Failure indicator
lights up
Indication on display
(if available)
Description - Causes - Solutions
“Service”
“bdd”
(in case your washing
machine has no display:
all lamps of the programme
flow bar light up)
Appliance stops during the programme. “Drum flaps
open” (the drum flaps have not been closed properly).
Push the “Reset” button for at least 3 seconds and wait
until the “Door open” lights up. Open lid and close
drum flaps, then select and start desired programme
again. If fault persists, notify our After-Sales Service.
from “F02” to “F35”
(except “F09”)
“Electrical module fault”.
Select and start “Drain” programme or push “Reset”
button for at least 3 seconds.
“F09”
“Water level too high” (after programme cancellation or
false operating). Switch off appliance and then switch it
on again, select programme “Drain” and start within 15
sec.
“FA”
“Waterstop fault”
Switch off appliance, pull out mains plug and turn water
tap off. Tilt appliance forward carefully to allow collected
water to flow out from the bottom. Then:
Plug in the appliance again.
Turn the water tap on (if water immediately flows into
the appliance without the appliance being started,
there is a failure; turn off the tap and notify After-Sales
Service).
Select and start the desired programme again.
“Fod”
“Overfoaming”
Too much foam interrupted the wash programme.
Select and start “Rinse & Spin” programme.
Afterwards select and start desired programme again,
using less detergent.
If faults persist, unplug the appliance, turn off the water
tap and contact our After-Sales Service
“Water tap
closed”
Appliance has no or insufficient water supply. The Start
(Pause) light blinks. Check whether:
Water tap is fully open and water supply pressure is
sufficient.
Kinks are present in water inlet hose.
Mesh filter of water supply hose is blocked (see “Care
and Maintenance”).
Water hose is frozen up.
Safety valve inspection window of your water supply
hose is red (provided your appliance has a water
supply hose as shown on picture 22 - see previous
chapter “Care and Maintenance”); replace the hose by
a new one available through our After-Sales Service or
your specialist dealer.
After problem has been removed, restart programme
by pressing Start (Pause)”. If the fault occurs again,
contact our After-Sales Service.
“Clean pump”
Waste water is not pumped out. The appliance stops in
the corresponding programme step; unplug it and check
whether:
Kinks are present in the drain hose.
Filter or pump is blocked (see chapter “Cleaning the
Filter/ Draining Residual Water”; make sure the water
has cooled before draining the appliance).
The drain hose is frozen up.
After problem has been removed, select and start “Drain”
programme or push “Reset” button for at least 3 seconds;
afterwards restart desired programme. If the fault occurs
again, contact our After-Sales-Service.
Description of failure indicators
If your washing machine has no display, check which of the previously described situations could be
the origin of the fault and follow the corresponding instructions.
E-07/2013
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Whirlpool AW ECO 9560 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Whirlpool AW ECO 9560 in the language / languages: English as an attachment in your email.

The manual is 3,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Whirlpool AW ECO 9560

Whirlpool AW ECO 9560 User Manual - German - 11 pages

Whirlpool AW ECO 9560 User Manual - Dutch - 11 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info