515832
15
Zoom out
Zoom in
Previous page
1/18
Next page
36
How to Purge Air Tubes
Thermal Insulation Piping:
Place the drain hose under the piping.
Insulating material: polythene foam over 6 mm in thickness.
NOTE: Drain hose is prepared by user.
Drain pipe should point downward for easy drain flow.
Do not twist the drain pipe, leave it sticking out or waving around, and do
not immerse the end in water. If an extension drain hose is connected to
the drain pipe, make sure it is thermally insulated when passing it through
the indoor unit.
When the piping is directed to the right, piping, power cord and drain pipe
should be thermally insulated and fixed at the rear of the unit with a piping
fixer.
1. Insert the pipe fixer into the slot.
2. Press to hook the pipe fixer onto the base.
Piping Connection:
Connect the indoor unit pipes using two wrenches. Pay special attention
to the torque allowed as shown below to prevent the pipes, connectors
and flare nuts from being deformed and damaged.
At first finger-tighten them, then use the wrenches.
For T3 climate kind models, 18 K and 24 K Liquid Side is (ø 6 or ¼ inch) and gas
side is (Ø 16 or 5/8inc).
Model Pipe size Torque
Nut
width
Min.
thickness
7-9-12 K Liquid Side (ø 6 or ¼ inch) 1.8 Kg.m 17 mm 0.6 mm
18,24 K Liquid Side (ø 10 or 3/8 inch) 3.5 Kg.m 22 mm 0.6 mm
7,9 K Gas Side (ø 10 or 3/8 inch) 3.5 Kg.m 22 mm 0.6 mm
12 K Gas Side (ø 12 or ½ inch) 5.5 Kg.m 24 mm 0.6 mm
18,24 K Gas Side (ø 16 or 5/8 inch) 7.5 Kg.m 27 mm 0.6 mm
Base
Piping fixer
Large pipe
Power
connecting cord
Power
connecting
cord 1 (for
heat-pump)
Drain hose
(prepared by user)
Small pipe
Thermally insulated
tube
Base
Piping fixer
Insert here
Large
pipe
Drain
hose
Small
pipe
Hook here
Defrost cable
(for heat-pump)
Unscrew and remove caps from 2 and 3-way valves.
Unscrew and remove cap from service valve.
Connect vacuum pump flexible hose to the service valve.
Start the vacuum pump for 10-15 minutes until it reaches an absolute vacuum of 10 mm Hg.
With the vacuum pump still running close the low pressure knob on the vacuum pump manifold. Then stop the vacuum pump.
Open the 2-way valve ¼ turn, then close it after 10 seconds. Check tightness of all joints using liquid soap or an
electronic leak detector.
Turn the 2 and 3-way valves stem. Disconnect the vacuum pump flexible hose.
Replace and tighten all valve caps.
NOTES:
Please read this manual before installing and using the appliance.
Do not let air enter the refrigerating system or discharge refrigerant when moving the air conditioner.
Test run the air conditioner after finishing installation, and record details of operation.
Type of fuse used on indoor unit control is 50 T, with rating 2.5 A,T,250 V.
The fuse for the whole unit is to be provided by the user according to the current at maximum power input or use
another over-current protective device instead.
The power connection for the air conditioner has to be made at the main power distribution which has to be of a low
impedance. In order to ensure the suitability of the equipment for connection, the user should consult the supply authority, if
necessary, to check that the service current capacity at the interface point is sufficient for the equipment. Refer to the rating
plate of the equipment for power consumption details. If the supply cord is damaged, it must be replaced by the manufacturer
or its service agent or similarly qualified person in order to avoid a hazard. When charging refrigerant into the system, make
sure to charge in liquid state, if the refrigerant of the appliance is R407C or R410a. Otherwise, the chemical composition of
the refrigerant inside the system may change and thus affect performance of the air conditioner. According to the character
of refrigerant (R410a), the pressure of the tube is very high, so ben sure to be careful when you install and repair the appliance.
Accessibility to the plug must be guaranteed even after the installation of the appliance to disconnect it if necessary.
If this is not possible, connect the appliance to a double-pole switching device with contact distance of at least 3 mm
placed in a position accessible even after installation.
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Whirlpool AMD 002 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Whirlpool AMD 002 in the language / languages: English as an attachment in your email.

The manual is 1,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Whirlpool AMD 002

Whirlpool AMD 002 User Manual - German - 18 pages

Whirlpool AMD 002 User Manual - Dutch - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info