After unpacking the hob, make sure that it has not been damaged during transport. In the event of problems, contact the dealer or your nearest After-sales Service.
TECHNICAL INFORMATION FOR THE INSTALLER
• Use protective gloves for handling, preparing and installing the product.
• This product can be embedded in a worktop 20 ÷ 60 mm thick.
• If there is no oven beneath the hob, insert a separator panel that has a surface at least equal to the opening in the work surface. This panel must
be positioned at a maximum distance of 150 mm below the upper surface of the work surface but, in no case less than 20 mm from the bottom
of the hob. In the case that you intend to install an oven beneath the hob, make sure that it is equipped with a cooling system. The manufacturer
declines all liability if another brand oven is installed beneath the hob.
Before installation, make sure that:
• the local gas delivery conditions (nature and pressure) are compatible with the settings of the hob (see the rating plate and injector table);
• the outer surfaces of the furniture or appliances adjacent to the hob are heat resistant according to local regulations;
• this appliance is not connected to a fume exhaust device. It shall be installed in accordance with current installation regulations. Particular attention shall
be given to the relevant requirements regarding ventilation;
• combustion products are discharged outdoors through specic hoods or wall and/or window mounted electrical fans.
GAS CONNECTION
WARNING
This operation must be performed by a qualied technician.
• The gas supply system must comply with local regulations.
• You can nd specic local regulations for some countries in the paragraph “Reference to Local Regulations”.
If no information concerning your Country is given, please ask details to your Installer.
• The connection of the hob to the gas pipe network or gas cylinder must be made by means of a rigid copper
or steel pipe with ttings complying with local regulations, or by means of a continuous-surface stainless steel
hose complying with local regulations. The maximum length of the hose is 2 linear metres.
• Connect elbow (A)* or (B)* supplied with to the hob inlet main pipe and interpose the washer (C) supplied,
in compliance with EN 549.
* Use elbow (A) for France and elbow (B) for all other destinations.
IMPORTANT: if a stainless steel hose is used, it must be installed so as not to touch any mobile part of
the furniture. It must pass through an area where there are no obstructions and where it is possible to
inspect it on all its length.
• After connection to the gas supply, check for leaks with soapy water. Light up the burners and turn the knobs
from max position to minimum position to check ame stability.
ELECTRICAL CONNECTION
WARNING
This operation must be performed by a qualied technician.
L
Earth
(yellow/green)
N
WARNING
• The electrical connections must comply with local regulations.
• The earthing of this appliance is compulsory by law.
• Do not use an extension cord.
IMPORTANT: the data relevant to the voltage and power absorption are indicated on the rating plate.
ASSEMBLY
After having cleaned the perimeter surface, apply the supplied gasket to the hob as shown in the gure.
Position the hob in the worktop opening made respecting the dimensions indicated in the Instruction.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Whirlpool AKT 5000 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Whirlpool AKT 5000 in the language / languages: English as an attachment in your email.
The manual is 1,82 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
