662520
3
Zoom out
Zoom in
Previous page
1/4
Next page
INSTALLATION
GAS CONNECTION
The gas supply system must comply with local regulations.
You can find specific local regulations for some countries in the paragraph “Reference to Local Regulations”. If no
information concerning your Country is given, please ask details to your Installer.
The connection of the hob to the gas pipe network or gas cylinder must be made by means of a rigid copper or steel
pipe with fittings complying with local regulations, or by means of a continuous-surface stainless steel hose complying
with local regulations. The maximum length of the hose is 2 linear metres.
Before connecting the tube to the elbow fitting (A), interpose the
washer (B) supplied, in compliance with EN 549.
Attention: if a stainless steel hose is used, it must be installed so as not to touch any mobile part of the furniture. It must pass
through an area where there are no obstructions and where it is possible to inspect it on all its length.
After connection to the gas supply, check for leaks with soapy water.
ELECTRICAL CONNECTION
The electrical connections must comply with local regulations.
The data relevant to the voltage and power absorption are indicated on the rating plate.
The earthing of this appliance is compulsory by law.
The manufacturer cannot be held responsible for any injury to persons or animals or damage to property arising from
failure to comply with these requirements.
When the hob is installed, provide a single-pole circuit breaker with a contact separation of at least 3 mm.
If necessary, the electrical power cable must be replaced exclusively with a power cable having identical characteristics
to the original supplied by the manufacturer (type H05V2V2-F T90°C or H05RR-F).
This operation must be performed by a qualified electrician.
Earth
(yellow/green)
L
N
2
3
1
ADJUSTMENT TO DIFFERENT TYPES OF GAS
If the appliance is intended to operate with a different gas from the gas type stated on the rating plate and orange sticker
applied on the top of the hob, change the injectors.
Remove the orange sticker and keep it with the instructions booklet.
Use pressure regulators suitable for the gas pressure indicated in the Product Description Sheet.
The gas nozzles must be changed by After Sales Service or a qualified technician.
Nozzles not supplied with the appliance must be ordered from After Sales Service.
Adjust the minimum setting of the taps.
Note
: when liquid petroleum gas is used (G30/G31), the minimum gas setting screw must be tightened as far as it will go.
Should you experience difficulty in turning the burners knobs, please contact the After Sales Service for the replacement of
the burner tap if found to be faulty.
REPLACING THE INJECTORS (see the injector table in the Product Description Sheet)
•Remove grids (A)
Extract burners (B)
Using a socket spanner of the appropriate size unscrew the injector (C)
Replace it with the injector suitable for the new type of gas.
Before installing the hob, remember to affix the gas calibration plate
supplied with the injectors in such a way that it covers the existing
information relating to gas calibration.
ADJUSTING MINIMUM GAS SETTING OF TAPS
To ensure that the minimum setting is correctly adjusted,
remove the knob and proceed as follows:
tighten the screw to reduce the height of the flame (-)
loosen the screw to increase the height of the flame (+)
The adjustment must be performed with the tap in minimum
gas setting position (small flame) .
The primary air of the burners does not need to be
adjusted.
At this stage, light up the burners and turn the knobs
from max position to minimum position to
check flame stability.
Upon completion of adjustment, reseal using sealing wax or
an equivalent material.
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Whirlpool AKT 351 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Whirlpool AKT 351 in the language / languages: English as an attachment in your email.

The manual is 1,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info