The instructions below, to be carried out in the order in which they are numbered, refer to the figures (with the same step numbers) given on the last pages of
this manual.
1.IMPORTANT:Work out the exact position where the hood is to be installed:
R1 = Middle of installation point and opening for the exhaust pipe.
FRONT= The side at the front of the hood.
LFT:left side of the hood.
RHT:right side of the hood.
N.B.:the same wording appears on numerous drawings to make it easier to understand the assembly instructions.
2.Place the template on the ceiling, taking into account the above-mentioned reference points and making sure the arrows stamped on the template
correspond with the front part of the hood (FRONT). Drill the number of holes of diameter as indicated.
Insert the wall plugs provided.
3.Half-tighten the screws as indicated (at corners), as these will be needed to fix the truss to the hood.
For Extractor Version only:Make an opening in the ceiling for the exhaust pipe.
4.Remove and set aside the screws securing the truss sections.
5.IMPORTANT:Adjust the extension of the truss, bearing in mind the following mathematical formula:
H (cm)= ( X-Y-M)+10.5.
H = Extension of truss to be calculated.
X= Distance from ceiling to hob.
Y= Minimum distance from the hobb to burners on hob ( 65cm gas hobs, 50cm electric hobs).
M = Height of motor unit from hood.
6.Fix the two sections of the truss using the screws as illustrated.
7.For Extractor Version only:fit an exhaust pipe to extract fumes and carry them to the outside.
This pipe must exit through the ceiling at a height as indicated in the drawing.
N.B.: H = Calculated truss extension (see assembly sequence 5).
N.B.:the exhaust pipe is not included in the packaging.
8.Remove the adhesive tape holding the control electronics box to the motor body.
N.B.:the figure is indicative only, the box may be temporarily fixed to other sides of the motor body.
9.Lift the box as shown.
10.Fully tighten the screws fixing the box to the motor body.
11.Slide the power supply cable into its housing.
12.Secure the cable with a cable clamp.
IMPORTANT:It is essential to carry out this operation. in order to avoid accidental disconnection of the cable.
13.Fix the truss to the hood using the screws as shown.
14.IMPORTANT:Attach the hood to the ceiling and fully tighten the screws.
15.IMPORTANT:Insert and tighten 2 screws (1 on each side) - these are OBLIGATORY safety anchors.
16.Fix the exhaust pipe to the connecting ring.
N.B.:the anchor band is not included in the packaging.
Carry out the electrical connection to the mains power supply.
17.For Filter Version only:Attach the deflector.
N.B.:The deflector comes in 3 pieces and must be assembled to size (the deflector must be ordered separately for this model).
18.Depending on the stability of the truss, decide if the upper support bracket should be fitted (with the screws as indicated).
N.B.:If the minimum extension was used, the bracket won't be necessary.
N.B.:We recommend placing the bracket at equal distances from the ceiling and the lower bracket welded to the truss.
19.Cut 2 magnetic strips to size and attach them to the inside of one of the two upper sections of the flue, as shown in the figure.
20.Assemble the upper sections of the flue to cover the truss. Secure the upper flue to the truss using screws, as shown in the figure.
21.Cut 2 magnetic strips to size and attach them to the inside of one of the two lower sections of the flue, as shown in the figure.
22.Assemble the lower sections of the flue to cover the truss.
23.Insert the flues in their seat above the covering hood, complete with the hood itself.
24.Remove the grease filter/s.
25.Secure the lower sections of the flues from inside the hood, using the screws as shown.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Whirlpool AKR504IX at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Whirlpool AKR504IX in the language / languages: English as an attachment in your email.
The manual is 2,52 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
