Manual Whirlpool akr 663 wh (page 11 of 32) (English, German, Dutch, French, Italian, Portuguese, Spanish)

132286

Zoom out

Zoom in

1/32

5019 318 33314/A

Extractor hood installation (A): fumes are extracted and expelled to the outside through an exhaust duct fixed to the flange

C (bayonet coupling). Always shut off the unused exhaust outlet with the plug D1 provided (if provided- bayonet coupling).

Important: some models are supplied with the upper hole B1 closed with a plug D1. Remove the plug to enable use.

Important! In some models, in order to use the rear exhaust outlet B2 the plastic part D2 or D3 must be removed first. Use

pliers and a cutter to remove it.

Filter version installation (F): If it is not possible to duct fumes and steam to the outside, the hood can be used in the filter

version by fitting a carbon filter/s (not supplied). In this way, fumes and steam are recycled through the front grille section

positioned above the control panel.

Check the position of the extraction/filter selector (inside the hood) G.

Fixing to the wall - Place the hood against the wall (or use the template H, if provided) and, using a pencil, mark the holes

(3 or 4 Ø 8mm holes), drill them, insert the rawlplugs J in the holes and 2 screws K in the top holes. Remove the grille and hang

the hood on the 2 screws. Next, from inside, insert the third (and fourth) screws L and screw them all down.

Fixing to the wall unit - Position the hood (or use the template H, if provided) and, using a pencil, mark the 4 Ø 6 mm holes

to be drilled on the bottom of the wall unit.

Fix the hood in place with 4 screws M from inside the wall unit.

Control panel

Light: move the switch to the right or press the next button to switch on.

Extraction speed: move the switch to the right or press the next button to increase extraction speed.

Grease filter - can be one of the following types:

Paper filter: must be replaced once a month or, if the top side is coloured, when the colour shows through the holes in the

grille.

Metal filter: must be washed once a month by hand or in a dishwasher, using a quick wash cycle with a low temperature.

To access the grease filter open the grille using the spring release catches E1 or E2 or E3 and release it from the retainers R1

or R2.

The self-supporting metallic filter has no support grille. To remove it, pull the spring release handlesE1 backwards and

remove the filter downwards.

Important! Over time, the metallic filter may become opaque; this in no way affects its filtering capacity.

Carbon filter - can be one of the following types:

Shaped V1: Remove the cover W by turning the knobs O through 90°.

Insert the carbon filter inside the special housing and secure it in place by turning the knob

O through 90°, then close the cover.

Replace every 4 months.

Rectangular V2: insert the rear edge first T and then the front (U) - replace every 6 months.

Circular V3: Bayonet coupling. Position the filter in the centre so that it covers the motor-protection grille, make sure that

the reference mark X1 or X2 or X3 or X4 on the carbon filter is aligned with the the reference mark Y on the fan shroud,

then turn clockwise; to remove, turn anti-clockwise, if provided with a tab Z remember to lift it up slightly first. Replace every

4 months.

Replacing the bulb/s - Remove the filters then remove the burnt-out bulb (E14 incandescent bulb, 40 W max). Refit the

filters.

G4 halogen bulb, 20 W max: use a small screwdriver or similar suitable tool to prise off.

Replace the bulb cover so that it clicks into position.

IF NL E PGBD GR

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Whirlpool akr 663 wh in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 2,04 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Whirlpool akr 663 wh Manual

Product: