662551
2
Zoom out
Zoom in
Previous page
1/4
Next page
ELECTRICAL CONNECTION
WARNING
This operation must be performed by a qualied technician.
WARNING
The electrical connections must
comply with local regulations.
The earthing of this applian-
ce is compulsory by law.
Do not use an extension
cord.
L
Earth
(yellow/green)
N
IMPORTANT: the data relevant to the voltage and power absorption are indicated on the rating plate.
ASSEMBLY
After having cleaned the perimeter surface,
apply the supplied gasket to the hob as shown in
the gure
Position the hob in the worktop opening made respecting the dimensions indicated in the Instruction.
NOTE: the power supply cable must be long enough to permit its upward extraction.
To secure the hob, use the brackets (A) provided with it. Fit the brackets into the relevant bores shown by the arrow and
fasten them by means of their screws in accordance with the thickness of the worktop (see the following gures).
Top 20 mm
Top 30-50 mm
ADJUSTMENT TO DIFFERENT TYPES OF GAS
WARNING
This operation must be performed by a qualied technician.
If the appliance is intended to operate with a dierent gas from the gas type stated on the rating plate and information
label on the top of the hob, change the injectors.
Remove the information label and keep it with the instructions booklet.
Use pressure regulators suitable for the gas pressure indicated in the Instruction.
The gas nozzles must be changed by After Sales Service or a qualied technician.
Nozzles not supplied with the appliance must be ordered from After Sales Service.
Adjust the minimum setting of the taps.
NOTE: when liquid petroleum gas is used (G30/G31), the minimum gas setting screw must be tightened as far as it
will go.
IMPORTANT: should you experience diculty in turning the burners knobs, please contact the After Sales Service
for the replacement of the burner tap if found to be faulty.
REPLACING THE INJECTORSsee the injector table in the Instruction
Remove grids (A).
Extract burners (B).
Using a socket spanner of the appropriate size unscrew
the injector (C), unscrew the injector to be replaced.
Replace it with the injector suitable for the new type of
gas.
Re-assemble the injector in (D).
If you have a multiple crown burner use side spanner to
replace the injector (E).
Before installing the hob, remember to ax the gas calibra-
tion plate supplied with the injectors in such a way that it
covers the existing information relating to gas calibration.
ADJUSTING MINIMUM GAS SETTING OF TAPS
To ensure that the minimum setting is correctly adjusted,
remove the knob and proceed as follows:
tighten screw to reduce the ame height (-);
loosen screw to increase the ame height (+).
The adjustment must be performed with the tap in minimum
gas setting position (small ame)
.
The primary air of the burners does not need to be adju-
sted.
At this stage, light up the burners and turn the knobs
from max position
to minimum position to check
ame stability.
Upon completion of adjustment, reseal using sealing wax or
an equivalent material.
REFERENCE TO LOCAL REGULATIONS
NL
Installation must be performed in accordance with standard
NBN D 51-003.
AFTERSALES SERVICE
Before calling the After-Sales Service, make sure you can give
the following information:
- type of fault or problem;
- exact model (written on the label axed to the in-
struction/warranty);
- service number that follows the word SERVICE on the
rating plate under the hob and on the label axed to
instruction/warranty;
- your complete address and phone number.
If any repairs are required, please contact an authorised
After-Sales Service, as indicated in the warranty.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Whirlpool AKR 3711 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Whirlpool AKR 3711 in the language / languages: English as an attachment in your email.

The manual is 0,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Whirlpool AKR 3711

Whirlpool AKR 3711 User Manual - Dutch - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info