-Only use the temperature probe recommended for this oven.
-Do not use harsh abrasive cleaners or sharp metal scrapers to clean the oven door glass
since they can scratch the surface, which may result in shattering of the glass.
-Ensure that the appliance is switched off before replacing the lamp to avoid the possibility
of electric shock.
-Do not use aluminium foil to cover food in the cooking vessel (only for ovens with cooking
vessel supplied).
-Use protective gloves to perform all unpacking and installation operations.
Scrapping of household appliances
-This appliance is manufactured with recyclable or reusable materials. Dispose of it in accordance with local waste disposal regulations. Before scrapping, cut off
the power supply cable.
-For further information on the treatment, recovery and recycling of household electrical appliances, contact your competent local authority, the collection service
for household waste or the store where you purchased the appliance.
After unpacking the oven, be sure that it has not been damaged during transport and that the oven door closes properly. In the event of problems, contact the dealer
or your nearest After-sales Service. To avoid any damage, only remove the oven from its polystyrene foam base at the time of installation.
PREPARING THE HOUSING UNIT
•Kitchen units in contact with the oven must be heat resistant (min 90°C).
•Carry out all cabinet cutting work before fitting the oven in the housing and carefully remove all wood chips and sawdust.
•After installation, the bottom of the oven must no longer be accessible.
•For correct appliance operation, do not obstruct the minimum gap between the worktop and the upper edge of the oven.
ELECTRICAL CONNECTION
Be sure the power voltage specified on the appliance dataplate is the same as the mains voltage. The dataplate is on the front edge of the oven (visible when the door
is open).
•Power cable replacement (cable type indicated on the connection label) must be carried out by a qualified electrician. Contact an authorized service centre.
INTERCONNECTING HOB AND OVEN
IMPORTANT: do not connect the oven to the power supply before you have finished connecting the oven and hob. Before connecting the oven to the power supply,
be sure that the hob is among the ones listed in the hob/oven pairing product sheet provided by your retailer. Connect the hob connectors to the oven connectors as
shown in the Installation Instruction, be sure that you match the colours and that the connector slots are aligned. Insert the connectors and push them in until they
click into place. Unscrew the nut of the ground screw located on the top covering of the oven and insert the yellow/green earth wire, leaving the washer in place.
Firmly retighten the nut of the ground screw.
IMPORTANT: if the hob terminals do not match the connection and colours of the sockets on the oven, require the adapter kit, code AMC 873, available from After Sales
Service.
GENERAL RECOMMENDATIONS
Before use:
-Remove cardboard protection pieces, protective film and adhesive labels from accessories.
-Remove the accessories from the oven and heat it at 200° for about an hour to eliminate the smell and fumes from the insulating materials and protective grease.
During use:
-Do not place heavy objects on the door as they could damage it.
-Do not cling to the door or hang anything from the handle.
-Do not cover the inside of the oven with aluminium foil.
-Do not pour water into the inside of a hot oven; this could damage the enamel coating.
-Do not drag pots or pans across the bottom of the oven as this could damage the enamel coating.
-Be sure that the electrical cables of other appliances do not touch hot parts of the oven or become trapped in the door.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Whirlpool AKP 732 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Whirlpool AKP 732 in the language / languages: English as an attachment in your email.
The manual is 2,42 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
