If a fault occurs, before contacting the After-sales Service, make the following checks to try and remedy the problem.
Most faults can be remedied by taking the following courses of action, quickly restoring normal appliance operation.
How the faults are shown on the display: Function number “F”x - blinkingError number “E”y - blinking0.5 sec. pause
The appliance...Possible causes...Solutions...
...is not working/will not start
-The appliance must be switched on.-Check the household circuit fuse if there is no power supply.
-The dishwasher door doesn’t close.-Check if the dishwasher’s door is closed.
-“Delayed start” option is ON.
-Check whether the “Delayed start” option (if available) has been selected. If it has, the appliance will only start once the set
time has elapsed. If necessary, set the delayed start to “0” (RESET the appliance).
...shows “F6E2”
-Water tap closed.-The water tap must be open.
-Kinked water inlet hose or clogged inlet filters.-The water inlet hose must not be kinked and the relative inlet filter in the water tap connector must not be clogged.
...shows “F6E7” or “F6E1”
-Water pressure too low.-The water tap must be fully open during water inlet (minimum capacity: 0.5 litres per minute).
-Kinked water inlet hose or clogged inlet filters.-The water inlet hose must not be kinked and the relative inlet filter in the water tap connector must not be dirty.
...shows “F6E3”/wash program ended too
early (dishes are dirty and wet)
-Dirty or clogged filters.-The filters must not be dirty or clogged.
-Too little water in the dishwasher’s water system.-Concave items (e.g. bowls, cups) must be arranged facing downwards in the rack.
-Drain hose incorrectly fitted.
-The drain hose must be fitted correctly (for high mounted appliances, leave min. 200-400 mm from the lower edge of the
appliance) - see Assembly instructions.
-High level of foam inside.-Repeat without detergent or wait until foam disappears.
...shows “F8E1”
-Dirty filters.-Clean the filters.
-Kinked drain hose.-The drain hose must not be kinked.
-Syphon hose connection closed.-The closure disk of the syphon hose connection must be removed.
After taking the above course of action, the fault message must be reset. In the majority of cases the fault is thus eliminated.
RESET:Press the CANCEL/Off button.
Close the door.
Water drains automatically for up to 1 minute.
The appliance is now ready to be restarted.
Crockery and cutlery...Possible causes...Solutions...
...are not perfectly clean/have food residues
-Too little space between dishes (incorrect arrangement of the
concave items in the rack).
-Arrange crockery so that items do not touch each other. Concave items (e.g. bowls, cups) must be arranged facing
downwards in the rack.
-Too little detergent; detergent too old or incorrectly stored.
-If necessary, use more detergent, observing the manufacturer’s indications as regards dosage. Always store detergent in a
dry place and do not store it for excessively long periods of time.
-Temperature not high enough for heavily soiled crockery.-For heavily soiled crockery, select a wash program with a higher temperature (see table of programs - page 1).
-Loading of the dishwasher using lower and upper rack at the
same time with “Half load/Multizone” option.
-If you select the “Half load/Multizone” option (if available), remember to load
only
the upper rack or
only
the lower rack to
increase washing power and thus obtain optimum wash results.
-Frequent use of Eco 50°C.
-In the event of frequent use of the Eco 50°C program (if available), from time to time select the Intensive 70°C program (if
available).
-Clogged spray arms, dirty filters or not fitted correctly.-The spray arms must not be clogged, the filters must not be dirty and must be fitted correctly (see page 5, “Maintenance and care“).
-Spray arms stuck impeded by crockery or cutlery.-The spray arms must be able to turn freely and must not be impeded by crockery or cutlery.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Whirlpool ADP 6966 ECO IX at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Whirlpool ADP 6966 ECO IX in the language / languages: English as an attachment in your email.
The manual is 1,91 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
