709123
7
Zoom out
Zoom in
Previous page
1/80
Next page
6
1 ― ON / OFF SWITCH FOR INTERIOR LIGHT. On / off switch for interior light I -(ON)
O (OFF)
4 ELECTRICITY SUPPLY INDICATOR. When the appliance is connected to the
electricity supply, the green indicator light is illuminated.
INSTALLATION AND OPERATING CONDITIONS OF THE
APPLIANCE
Preparing the appliance for operation
It is recommended to prepare the appliance for operation with a helper.
Remove package. Lift the appliance away from foamed polystyrene base.
Therefore take out adhesive tapes from sides and simply lift the appliance up and
take out the board. Strip adhesive tapes off and open the door. Remove the spacer
above the door.
When positioning the appliance in chosen location, it will move more easily into
position if you lift the front a little and incline it backward allowing it to roll on its
casters. When placing, moving, lifting the appliance, do not hold the door
handles, do not pull the condenser at the rear part of the refrigerator and
do not touch the compressor unit.
Take two supports from the bag and insert them into the guides at the top back part
of the appliance (see fig. 2, page 1).
If the appliance is brought in from the cold (temperature is not higher than +12
°C), you should wait for two hours before connecting it to the mains.
The appliance should not be connected to the mains until all packing and
transport materials aren’t removed. Suitably dispose the packaging material.
Positioning
Place the appliance in a dry, well ventilated room.
WARNING! The appliance should not be operated in an unheated room or
porch. Place the appliance away from heat sources such as kitchen
stove/oven, radiators, or direct sunlight.
WARNING! The appliance must not touch any pipes for heating, gas or
water supply or any other electrical devices.
Do not cover the ventilation holes at the top of the appliances it must be a good air
circulation around the appliance. There should be a gap of at least 10 cm between
the top of the appliance body and any furniture that may be above it. If this
requirement is not followed, the appliance consumes more electrical energy and its
compressor may overheat.
If the appliance is placed in a corner, a gap of at least 1 cm must be left between the
appliance body and the wall (see fig. 3, page 1).
The appliance must stand on a level surface and must not touch the wall. If
necessary, regulate the height of the appliance by adjusting the levelling feet: by
turning them clockwise the front of the appliance rises, by turning them counter
clockwise it comes down. If the appliance is tilted slightly backward the doors will
close by themselves.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Whirlpool ADN 201-2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Whirlpool ADN 201-2 in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 1,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info