128181
4
Zoom out
Zoom in
Previous page
1/8
Next page
4
3. HOW TO USE THE APPLIANCE
c. How to adjust the rinse aid dosage regulator
The rinse aid dosage can be adjusted to the detergent used. The lower the setting, the less
rinse aid is dispensed (factory setting: position 4).
Press the button
2
to open the cover.
Using a coin or similar object, turn the arrow to the desired setting.
After adjusting the rinse aid setting, shut the cover again.
If there are streaks: reduce the dosage by turning the dial to a lower setting (1-3). If crockery is
not perfectly dry: increase the dosage by turning the dial to a higher setting (5-6). Plastic dishes
have more difficulty drying and a higher rinse aid setting will not improve the situation.
HOW TO CHECK/FILL/ADJUST SALT
Only use
regeneration salt specifically for dishwashers.
a. How to check the salt level
Depending on the model, check the visual indicator . The window on the salt reservoir cap is clear when salt
needs to be added and orange when the salt present is sufficient. In the case of appliances with an electric indicator on
the control panel, the salt indicator lamp lights up red when salt needs to be added.
b. How to fill the salt container
- Remove the lower rack.
- Turn the salt container cap anti-clockwise to open it.
- When using the dishwasher for the first time, fill the salt container to the rim with water.
- Using the funnel provided, fill with regeneration salt to the rim (the first time,
min. 1.5 kg/max. 2 kg).
- Stir with the handle of a wooden spoon to help dissolve the salt.
- Close the cap of the salt container by turning it clockwise.
- Reinsert the lower rack.
Once regeneration salt is added,
immediately
start a wash programme (the “Pre-wash”
programme alone is
not
sufficient). Residual saline solution or grains of salt can lead to deep-
down corrosion, irreparably damaging the stainless steel components. The guarantee is not
applicable if faults are caused by such circumstances.
The salt level indicator lamp may remain lit for the duration of several wash cycles.
If the water hardness level falls within category 1 (soft),
no
salt is required.
c. How to set the water hardness level
- Switch on the appliance.
- Select the 2nd programme “P2” - consult the table 1.1 in chapter 1.
- Press the START button for at least 5 seconds until the START indicator lamp flashes.
- The set water hardness level is shown on the display (if present) or the START button flashes.
- With each successive touch of the START button the setting increases and when it reaches 7 it returns to 1 again.
- The appliance must be switched off to memorise the new setting.
Water hardness level is factory set at 3 for medium-hard water (display 4 or 4 flashes of the
START button).
Water hardness level 4 with combined action detergent
Even if you use a combined action detergent which includes salt, you must still add regeneration
salt since such detergents are not effective enough at softening hard water.
If the appliance is equipped with the function “Select detergent” (see chapter “1. Overview”),
set the detergent dispenser system to the “no salt” setting so that the salt indicator lamp remains
activated (“Detergent with rinse aid”).
Water hardness German degrees
°dH
French degrees
°fH
English degrees
°eH
Flashing frequency
or display setting
1 soft 0 - 5 0 - 9 0 - 6.3 1 / 1x
1 - 2 medium 6 - 10 10 - 18 7 - 12.6 2 / 2x
2 medium 11 - 15 19 - 27 13.3 - 18.9 3 / 3x
3 medium-hard 16 - 21 28 - 37 19.6 - 25.9 4 / 4x
4 hard 22 - 28 38 - 50 26.6 - 35 5 / 5x
4 very hard 29 - 35 51 - 63 35.7 - 44.1 6 / 6x
4 extremely hard 36 - 60 64 - 107 44.8 - 74.9 7 / 7x
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Whirlpool adg 9929 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Whirlpool adg 9929 2 in the language / languages: English as an attachment in your email.

The manual is 0,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Whirlpool adg 9929 2

Whirlpool adg 9929 2 User Manual - German - 8 pages

Whirlpool adg 9929 2 User Manual - Dutch - 8 pages

Whirlpool adg 9929 2 User Manual - French - 8 pages

Whirlpool adg 9929 2 User Manual - Italian - 8 pages

Whirlpool adg 9929 2 User Manual - Portuguese - 8 pages

Whirlpool adg 9929 2 User Manual - Spanish - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info